To Next Page
N
nguyenkiaraSep 4, 2025
What to do if my Eaton UPS filtered outlets 8 are not supplied?
- JJonathan AustinSep 4, 2025
The wall outlet may not be supplied. Try resetting the circuit breaker.
What to do if my Eaton UPS filtered outlets 8 are not supplied?
The wall outlet may not be supplied. Try resetting the circuit breaker.
What to do if EcoControl outlets keep powered when main application (Master outlet) is stopped on my Eaton Ellipse ECO 1600?
If the EcoControl outlets on your Eaton UPS remain powered even after the main application (Master outlet) is stopped, it indicates that the EcoControl function is either not activated or not properly set. Activate or properly set the EcoControl function using the software provided with the product.
What to do if the telephone line is disturbed or modem access is not possible with my Eaton Ellipse ECO 1600 UPS?
If you are experiencing a disturbed telephone line or inability to access the modem while using your Eaton UPS, it could be due to surge protection on the telephone line no longer being provided. Disconnect the telephone line from the wall outlet. Call after-sales support.
What does it mean if the green LED 10 is off and the filtered outlets 8 are supplied on my Eaton UPS?
If the green LED 10 is off and the filtered outlets 8 are still supplied on your Eaton UPS, it means that surge protection is no longer provided. Call after-sales support.
What to do if the connected devices are not supplied when AC power fails on my Eaton Ellipse ECO 1600?
If the devices connected to your Eaton UPS are not supplied with power when AC power fails, it's likely because the devices are not connected to the battery backup outlets 9. Ensure that the devices are connected to the battery backup outlets 9.
What to do if the filtered outlets 8 are not supplied with power on my Eaton Ellipse ECO 1600?
If the filtered outlets 8 on your Eaton UPS are not supplied with power, there are two possible causes: 1. The wall outlet itself may not be supplied with power. Ensure the wall outlet has power. 2. Circuit breaker 13, located under the UPS, has been tripped by an overload on the UPS output. Disconnect excess equipment and reset the circuit breaker 13 by pressing the corresponding button.
What to do if AC power is available, but my Eaton Ellipse ECO 1600 UPS operates on battery power?
If your Eaton UPS is operating on battery power even when AC power is available, it could be due to circuit breaker 13, located under the UPS, having been tripped by an overload on the UPS output. Disconnect excess equipment and reset the circuit breaker 13 by pressing the corresponding button to resolve this issue.
What to do if the telephone line is disturbed when using Eaton UPS?
Surge protection on the telephone line may no longer be provided. Check the modem connections.
What to do if EcoControl outlets keep powered when main application (Master outlet) is stopped in Eaton UPS?
The EcoControl function might not be activated or properly set. Activate or properly set the EcoControl function using the software provided with the product.
Why is my Eaton Ellipse ECO 1600 UPS beeping continuously and the green button 12 flashing?
The UPS battery backup outlets 9 may be overloaded. Try reducing the load on these outlets.
General| Power Rating | 1600 VA |
|---|---|
| Output Power Capacity | 1000 W |
| Output Voltage | 230V |
| Output Voltage Tolerance | +/- 10% |
| Number of Outlets | 8 |
| Communication Ports | USB, RS-232 |
| Humidity | 0-95% non-condensing |
| Warranty | 2 years |
| Topology | Line-interactive |
| Outlets Type | IEC C13 |
| Battery Type | Sealed lead-acid (SLA) |
| Efficiency | 95% |
| Frequency Range | 50/60 Hz |
| Operating Temperature | 0 to 40°C |
| Storage Temperature | -15 to +45°C |
| Typical Backup Time at 50% Load | 15 minutes |
| Typical Recharge Time | 4-6 hours to 90% |
Read safety instructions booklet (3) and this manual (2) before installation and heed warnings.
Illustrates connections for FR/DIN, IEC, USB models and network/modem options.
Covers UPS operation (On/Off) and warranty registration details.
Guidelines on battery service life reduction and safe disposal.
Step-by-step instructions for changing batteries in different Ellipse ECO models.
Details UPS power, voltage, frequency, current, and protection ratings.
Results of surge wave protection tests and dielectric isolation ratings.
Specifies suitable equipment for UPS and general operating conditions.
Details how to connect UPS, operate battery backup, and manage EcoControl outlets.
Common issues, diagnostics, and solutions for UPS operation.
Adjusting AC power sensitivity and audio alarm modes for the UPS.
