To Next Page
E
Evelyn EdwardsSep 4, 2025
What to do if my Eaton Ellipse ECO 650 filtered outlets 8 are not supplied?
- WwhayesSep 4, 2025
The wall outlet may not be supplied. Try resetting the circuit breaker.
What to do if my Eaton Ellipse ECO 650 filtered outlets 8 are not supplied?
The wall outlet may not be supplied. Try resetting the circuit breaker.
What to do if EcoControl outlets keep powered when main application (Master outlet) is stopped on my Eaton Ellipse ECO 650 UPS?
If the EcoControl outlets on your Eaton UPS remain powered even after the main application (Master outlet) is stopped, it indicates that the EcoControl function is either not activated or not properly set. Activate or properly set the EcoControl function using the software provided with the product.
What to do if the telephone line is disturbed or modem access is not possible with my Eaton Ellipse ECO 650?
If you are experiencing a disturbed telephone line or inability to access the modem while using your Eaton UPS, it could be due to surge protection on the telephone line no longer being provided. Disconnect the telephone line from the wall outlet. Call after-sales support.
What does it mean if the green LED 10 is off and the filtered outlets 8 are supplied on my Eaton Ellipse ECO 650 UPS?
If the green LED 10 is off and the filtered outlets 8 are still supplied on your Eaton UPS, it means that surge protection is no longer provided. Call after-sales support.
What to do if the connected devices are not supplied when AC power fails on my Eaton Ellipse ECO 650?
If the devices connected to your Eaton UPS are not supplied with power when AC power fails, it's likely because the devices are not connected to the battery backup outlets 9. Ensure that the devices are connected to the battery backup outlets 9.
What to do if the filtered outlets 8 are not supplied with power on my Eaton Ellipse ECO 650 UPS?
If the filtered outlets 8 on your Eaton UPS are not supplied with power, there are two possible causes: 1. The wall outlet itself may not be supplied with power. Ensure the wall outlet has power. 2. Circuit breaker 13, located under the UPS, has been tripped by an overload on the UPS output. Disconnect excess equipment and reset the circuit breaker 13 by pressing the corresponding button.
What to do if AC power is available, but my Eaton UPS operates on battery power?
If your Eaton UPS is operating on battery power even when AC power is available, it could be due to circuit breaker 13, located under the UPS, having been tripped by an overload on the UPS output. Disconnect excess equipment and reset the circuit breaker 13 by pressing the corresponding button to resolve this issue.
What to do if the telephone line is disturbed when using Eaton Ellipse ECO 650?
Surge protection on the telephone line may no longer be provided. Check the modem connections.
What to do if EcoControl outlets keep powered when main application (Master outlet) is stopped in Eaton Ellipse ECO 650?
The EcoControl function might not be activated or properly set. Activate or properly set the EcoControl function using the software provided with the product.
Why is my Eaton UPS beeping continuously and the green button 12 flashing?
The UPS battery backup outlets 9 may be overloaded. Try reducing the load on these outlets.
General| Power Rating | 650 VA |
|---|---|
| Output Voltage | 230V |
| USB Port | Yes |
| Surge Protection | Yes |
| Waveform Type | Stepped approximation to a sinewave |
| Output Power Capacity | 400 W |
| Battery Type | Sealed lead-acid |
| Number of Outlets | 4 |
| Topology | Line-interactive |
| Communication | USB port |
| Efficiency | Typical 95% |
| Frequency Range | 50/60 Hz |
| Typical Recharge Time | 4-6 hours |
| Operating Temperature | 0 to +40°C |
| Relative Humidity | 0-95% non-condensing |
| Standards | IEC 62040-3 |
| Safety Approvals | CE |
| Outlets | 4 IEC outlets |
Shows connection for FR/DIN UPS models to AC power.
Illustrates connecting UPS models and EcoControl feature.
Details network and modem surge protection connection via UPS.
Demonstrates connecting UPS to a computer via USB.
Explains how to turn the UPS on and off using the button.
Provides the website to register the product warranty online.
Provides safety precautions for battery disposal and handling.
Details the steps for safely replacing the UPS battery.
Describes the intended use and limitations of the UPS product.
Explains how EcoControl outlets manage peripheral power consumption.
Details how to adjust EcoControl detection threshold for optimal performance.
Guides on connecting the UPS to power and peripherals.
Details operation of Master and EcoControl outlets, LEDs, and buttons.
Lists common UPS problems, their diagnostics, and solutions.
Configuring UPS sensitivity to AC power variations.
Customizing the audio alarm behavior during battery operation.
