To Next PageTo Next PageWhy is the green button 12 flashing frequently and the audio alarm beeping on my Eaton Ellipse ECO 500?
The green button 12 might be flashing frequently, and the audio alarm beeping because the Eaton UPS is frequently operating on battery power due to a poor-quality AC power source. To resolve this, have the electrical installation checked by a professional or try using another wall outlet.
What does it mean if the red LED 11 is flashing on my Eaton UPS?
If the red LED 11 is flashing on your Eaton UPS, it means that the battery has reached the end of its service life. You should have the battery replaced.
What does it mean if the red LED 11 is on and the audio alarm beeps every 30 seconds on my Eaton UPS?
If the red LED 11 is on and the audio alarm beeps every 30 seconds on your Eaton UPS, it indicates a fault has occurred on the UPS and the battery backup outlets 9 are no longer supplied. Call after-sales support.
What to do if AC power is available, but my Eaton UPS operates on battery power?
If your Eaton UPS is operating on battery power even when AC power is available, it could be due to circuit breaker 13, located under the UPS, having been tripped by an overload on the UPS output. Disconnect excess equipment and reset the circuit breaker 13 by pressing the corresponding button to resolve this issue.
What to do if the filtered outlets 8 are not supplied with power on my Eaton Ellipse ECO 500 UPS?
If the filtered outlets 8 on your Eaton UPS are not supplied with power, there are two possible causes: 1. The wall outlet itself may not be supplied with power. Ensure the wall outlet has power. 2. Circuit breaker 13, located under the UPS, has been tripped by an overload on the UPS output. Disconnect excess equipment and reset the circuit breaker 13 by pressing the corresponding button.
What to do if the connected devices are not supplied when AC power fails on my Eaton Ellipse ECO 500?
If the devices connected to your Eaton UPS are not supplied with power when AC power fails, it's likely because the devices are not connected to the battery backup outlets 9. Ensure that the devices are connected to the battery backup outlets 9.
What does it mean if the green LED 10 is off and the filtered outlets 8 are supplied on my Eaton Ellipse ECO 500 UPS?
If the green LED 10 is off and the filtered outlets 8 are still supplied on your Eaton UPS, it means that surge protection is no longer provided. Call after-sales support.
What to do if the telephone line is disturbed or modem access is not possible with my Eaton Ellipse ECO 500 UPS?
If you are experiencing a disturbed telephone line or inability to access the modem while using your Eaton UPS, it could be due to surge protection on the telephone line no longer being provided. Disconnect the telephone line from the wall outlet. Call after-sales support.
What to do if green button 12 flashes and the audio alarm beeps continuously on my Eaton UPS?
If the green button 12 is flashing and the audio alarm is beeping continuously on your Eaton UPS, it indicates that the battery backup outlets 9 are overloaded. Disconnect some of the equipment connected to the battery backup outlets 9.
What to do if EcoControl outlets keep powered when main application (Master outlet) is stopped on my Eaton Ellipse ECO 500 UPS?
If the EcoControl outlets on your Eaton UPS remain powered even after the main application (Master outlet) is stopped, it indicates that the EcoControl function is either not activated or not properly set. Activate or properly set the EcoControl function using the software provided with the product.
General| Output Power | 300 W |
|---|---|
| Input Voltage | 230V |
| Communication Ports | USB |
| Surge Protection | Yes |
| Humidity | 0-95% non-condensing |
| Warranty | 2 years |
| Output Voltage | 230 V |
| Input Frequency | 50-60 Hz |
| Output Frequency | 50-60 Hz |
| Number of Outlets | 4 |
| Battery Type | Sealed Lead-Acid |
| Operating Temperature | 0-40°C |
| Storage Temperature | -15 to +45°C |
