What does it mean when green LED 10 is off on my Eaton Ellipse 375?
If green LED 10 is off and the filtered outlets 8 are supplied on your Eaton UPS, it means that surge protection is no longer provided. Call after-sales support.
What to do if red LED 11 is on and alarm beeps on my Eaton Ellipse 375 UPS?
If red LED 11 is on and the audio alarm beeps every 30 seconds on your Eaton UPS, it indicates a fault has occurred on the UPS, and the battery backup outlets 9 are no longer supplied. Call after-sales support.
Why is my Eaton UPS beeping and the red LED 12 is on?
The red LED 12 turns on, and the audio alarm beeps every 30 seconds because the UPS battery backup outlets 9 are overloaded. To resolve this, disconnect excess equipment connected to the battery backup outlets 9.
What does it mean when red LED 11 flashes on Eaton Ellipse 375?
If red LED 11 flashes on your Eaton UPS, it indicates that the battery has reached the end of its service life. To resolve this, have the battery replaced.
What to do if AC power is available, but my Eaton UPS operates on battery power?
If your UPS operates on battery power even when AC power is available, it could be because circuit breaker 14, located under the UPS, has been tripped by an overload on the UPS output. Disconnect excess equipment and reset the circuit breaker 14 by pressing the corresponding button.
What to do if my Eaton UPS green button 13 flashes frequently and the alarm beeps?
If the green button 13 on your Eaton UPS flashes frequently and the audio alarm beeps, it indicates that the UPS frequently operates on battery power because the AC power source is of poor quality. To resolve this, have the electrical installation checked by a professional or use another wall outlet.
What to do if my Eaton Ellipse 375 filtered outlets 8 are not supplied?
If the filtered outlets 8 on your Eaton UPS are not supplied, it could be due to two reasons: * The wall outlet is not supplied, in which case you should supply power to the wall outlet. * Circuit breaker 14, located under the UPS, has been tripped by an overload on the UPS output. If this is the case, disconnect excess equipment and reset the circuit breaker 14 by pressing the corresponding button.
Why is my telephone line disturbed when using Eaton Ellipse 375 UPS?
If the telephone line is disturbed or modem access is not possible when using your Eaton UPS, it might be because surge protection on the telephone line is no longer provided. Disconnect the telephone line from the wall outlet. For further assistance, you may need to call after-sales support.
How to fix Eaton Ellipse 375 filtered outlets 8 not working?
If the filtered outlets 8 are not supplied with power, it could be due to the wall outlet not being supplied with power. In this case, supply power to the wall outlet. Alternatively, circuit breaker 14, located under the UPS, may have been tripped by an overload on the UPS output. If so, disconnect excess equipment and reset the circuit breaker 14 by pressing the corresponding button.
What to do if connected devices aren't supplied when AC power fails on my Eaton Ellipse 375 UPS?
If the connected devices are not supplied when AC power fails, ensure the devices are connected to the battery backup outlets 9. Connect the devices to the battery backup outlets 9.
General| Input Voltage | 230 V |
|---|---|
| Input Frequency | 50/60 Hz |
| Output Voltage | 230 V |
| Output Frequency | 50/60 Hz |
| Number of Outlets | 4 |
| Output Receptacles | IEC 320 C13 |
| Surge Protection | Yes |
| Power Capacity | 375 VA |
| Battery Type | Sealed Lead Acid |
| Typical Backup Time (Full Load) | 5 minutes |
| Operating Temperature | 0 - 40 °C |
| Storage Temperature | -15 - 45 °C |
| Humidity | 0 - 95% (non-condensing) |
To Next Page