What to do if Eaton Power Supply operates on battery when AC power is available?
If your Eaton Power Supply operates on battery power even when AC power is available, it's possible that the circuit breaker located under the UPS has been tripped due to an overload. To resolve this, disconnect some of the connected equipment to reduce the load and then reset the circuit breaker by pressing the corresponding button.
What does it mean if red LED 11 is on and the audio alarm beeps every 30 seconds on my Eaton Ellipse 375 UPS?
If the red LED 11 is on and the audio alarm beeps every 30 seconds, it indicates a fault has occurred on the UPS, and the battery backup outlets 9 are no longer supplied.
What does it mean if green LED 10 is off on my Eaton UPS?
If the green LED 10 is off and the filtered outlets 8 are supplied, it indicates that surge protection is no longer provided.
How to fix disturbed telephone line or modem access with Eaton Ellipse 375?
If the telephone line is disturbed or modem access is not possible while using an Eaton UPS, it may be because surge protection on the telephone line is no longer provided. Disconnect the telephone line from the wall outlet.
What to do if red LED 12 is on and alarm beeps on my Eaton Ellipse 375?
If the red LED 12 is on and the audio alarm beeps every 30 seconds, it means that the UPS battery backup outlets 9 are overloaded. To resolve this, disconnect excess equipment connected to the battery backup outlets 9.
What to do if my Eaton Ellipse 375 filtered outlets 8 are not supplied?
If the filtered outlets 8 on your Eaton UPS are not supplied, it could be due to two reasons: * The wall outlet is not supplied, in which case you should supply power to the wall outlet. * Circuit breaker 14, located under the UPS, has been tripped by an overload on the UPS output. If this is the case, disconnect excess equipment and reset the circuit breaker 14 by pressing the corresponding button.
What does it mean when green LED 10 is off on my Eaton Ellipse 375?
If green LED 10 is off and the filtered outlets 8 are supplied on your Eaton UPS, it means that surge protection is no longer provided. Call after-sales support.
Why is my telephone line disturbed when using Eaton Ellipse 375 UPS?
If the telephone line is disturbed or modem access is not possible when using your Eaton UPS, it might be because surge protection on the telephone line is no longer provided. Disconnect the telephone line from the wall outlet. For further assistance, you may need to call after-sales support.
What to do if connected devices aren't supplied when AC power fails on my Eaton Ellipse 375 UPS?
If the connected devices are not supplied when AC power fails, ensure the devices are connected to the battery backup outlets 9. Connect the devices to the battery backup outlets 9.
How to fix Eaton Ellipse 375 filtered outlets 8 not working?
If the filtered outlets 8 are not supplied with power, it could be due to the wall outlet not being supplied with power. In this case, supply power to the wall outlet. Alternatively, circuit breaker 14, located under the UPS, may have been tripped by an overload on the UPS output. If so, disconnect excess equipment and reset the circuit breaker 14 by pressing the corresponding button.
General| Input Voltage | 230 V |
|---|---|
| Input Frequency | 50/60 Hz |
| Output Voltage | 230 V |
| Output Frequency | 50/60 Hz |
| Number of Outlets | 4 |
| Output Receptacles | IEC 320 C13 |
| Surge Protection | Yes |
| Power Capacity | 375 VA |
| Battery Type | Sealed Lead Acid |
| Typical Backup Time (Full Load) | 5 minutes |
| Operating Temperature | 0 - 40 °C |
| Storage Temperature | -15 - 45 °C |
| Humidity | 0 - 95% (non-condensing) |
To Next Page