ebm-papst W3G910-KS35-03 - User Manual

Operating instructions
W3G910-KS35-03
Translation of the original operating instructions
ebm-papst Mulfingen GmbH & Co. KG
Bachmühle 2
D-74673 Mulfingen
Phone +49 (0) 7938 81-0
Fax +49 (0) 7938 81-110
info1@de.ebmpapst.com
www.ebmpapst.com
CONTENTS
1. SAFETY REGULATIONS AND INFORMATION
11. SAFETY REGULATIONS AND INFORMATION
Read these operating instructions carefully before starting work on the
device. Observe the following warnings to prevent malfunctions or
danger to persons.
These operating instructions are to be regarded as part of the device.
The device is only to be sold or passed on together with the operating
instructions.
These operating instructions may be duplicated and distributed to inform
about potential dangers and their prevention.
1.1 Hazard levels for warnings
11.1 Hazard levels for warnings
These operating instructions use the following hazard levels to indicate
potentially hazardous situations and important safety regulations:
DANGER
Indicates an imminently hazardous situation which will result in
death or serious injury if the specified actions are not taken.
Compliance with the instructions is imperative.
WARNING
Indicates a potentially hazardous situation which can result in
death or serious injury if the specified actions are not taken.
Exercise extreme caution while working.
CAUTION
Indicates a potentially hazardous situation which can result in
minor or moderate injury or damage to property if the specified
actions are not taken.
NOTE
A potentially harmful situation can occur and, if not avoided, can
lead to property damage.
1.2 Staff qualifications
11.2 Staff qualifications
The device may only be transported, unpacked, installed, operated,
maintained and otherwise used by suitably qualified, trained and
authorized technical staff.
Only authorized specialists are permitted to install the device, to carry
out a test run and to perform work on the electrical installation.
1.3 Basic safety rules
11.3 Basic safety rules
The safety hazards associated with the device must be assessed again
following installation in the final product.
The locally applicable industrial safety regulations are always to be
observed when working on the device.
Keep the workplace clean and tidy. Untidiness in the work area
increases the risk of accidents.
Note the following when working on the device:
; Do not perform any modifications, additions or conversions on the
device without the approval of ebm-papst.
1.4 Voltage
11.4 Voltage
; Check the device's electrical equipment at regular intervals; see
Chapter 6.3 Safety inspection.
; Replace loose connections and defective cables immediately.
DANGER
Electrically charged device
Risk of electric shock
→ When working on an electrically charged device, stand on a
rubber mat.
21.5 Safety and protective features
21.6 Electromagnetic radiation
21.7 Mechanical movement
21.8 Emissions
21.9 Hot surface
21.10 Transport
31.11 Storage
32. INTENDED USE
43. TECHNICAL DATA
43.1 Product drawing
53.2 Nominal data
53.3 Data according to Commission Regulation (EU) 327/2011
53.4 Technical description
63.5 Mounting data
63.6 Transport and storage conditions
63.7 Electromagnetic compatibility
64. CONNECTION AND STARTUP
64.1 Mechanical connection
64.2 Electrical connection
84.3 Connection in terminal box
94.4 Factory settings
104.5 Connection diagram
114.6 Configuration options
124.7 Equivalent circuit diagrams
134.8 Checking connections
134.9 Switching on the device
134.10 Switching off the device
135. INTEGRATED PROTECTIVE FEATURES
136. MAINTENANCE, MALFUNCTIONS, POSSIBLE
CAUSES AND REMEDIES
146.1 Warning/status codes
156.2 Cleaning
156.3 Safety inspection
156.4 Disposal
Item no. 55591-5-9970 · ENU · Change 209539 · Approved 2021-02-09 · Page 1 / 16
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com

Summary

Safety Regulations and Information

Hazard Levels for Warnings

Explains hazard level symbols and their meanings for warnings.

Staff Qualifications

Specifies required qualifications for personnel handling the device.

Basic Safety Rules

Outlines fundamental safety practices to be observed when working with the device.

Voltage Information

Provides information regarding the voltage levels relevant to the device's operation.

Safety and Protective Features

Details the safety mechanisms and protective features integrated into the device.

Electromagnetic Radiation

Discusses potential interference from electromagnetic radiation and shielding measures.

Mechanical Movement Hazards

Warns about hazards related to rotating parts and potential injuries.

Emissions and Noise

Addresses potential noise emissions and required safety measures for hearing protection.

Hot Surface Warning

Alerts users to the risk of burns from hot surfaces on the device housing.

Transport Guidelines

Provides guidelines and safety precautions for transporting the fan unit.

Storage Conditions

Details the proper conditions and procedures for storing the device to maintain its integrity.

Intended Use

Improper Use

Lists prohibited operations and potential hazards associated with misuse of the device.

Technical Data

Product Drawing

Presents a technical illustration of the product with key dimensions and labels.

Nominal Data

Lists the device's key specifications, performance data, and electrical ratings.

EU Regulation Data

Provides energy efficiency data as per EU regulation requirements.

Technical Description

Details the materials, construction, and technical features of the device.

Mounting Data

Specifies requirements and recommendations for mounting the device securely.

Transport and Storage Conditions

Outlines temperature limits and conditions for transport and storage.

Electromagnetic Compatibility

Describes EMC immunity and emission standards the device complies with.

Connection and Startup

Mechanical Connection

Guides users through the physical installation and connection procedures for the device.

Electrical Connection and Safety

Covers electrical hookup, requirements, supply, fuses, RCCB, leakage, and locked-rotor protection.

Terminal Box Connection and Routing

Details connecting cables in the terminal box, preparing cables, data, and routing.

Factory Settings

Lists the default configuration parameters set by the manufacturer for the device.

Connection Diagram

Illustrates the electrical connections for power supply and control interfaces.

Configuration Options

Details various configurable inputs/outputs and their functions for device setup.

Equivalent Circuit Diagrams

Provides schematic diagrams for understanding input and output circuit behavior.

Checking Connections

Outlines steps to verify all electrical and mechanical connections are secure and correct.

Switching On the Device

Describes the procedure for safely powering on the device after installation.

Switching Off the Device

Explains how to properly shut down the device during operation or for maintenance.

Integrated Protective Features

Maintenance, Malfunctions, Causes and Remedies

Warning and Status Codes

Explains the LED indicators and status codes for diagnosing device malfunctions.

Cleaning Instructions

Provides instructions and precautions for cleaning the device to prevent damage.

Safety Inspection Procedures

Lists periodic checks and inspections to ensure the device's safe and reliable operation.

Disposal Recommendations

Offers general recommendations for the environmentally sound disposal of the product.

Disassembly Procedures

Guides on the safe disassembly of the product into components for disposal.

Component Disposal

Details how to separate and recycle various product materials and components.

ebm-papst W3G910-KS35-03 Specifications

General

Manufacturer	ebm-papst
Type	Axial Fan
Model Number	W3G910-KS35-03
Frequency	50/60 Hz
Speed	1350 rpm
Housing Material	Aluminum
Protection Class	IP54
Dimensions	910 mm (diameter)
Voltage	230 V