31
Designed in
Summerville, SC
Support: Support.Eccotemp.com Shop Online: www.Eccotemp.com Phone: 866-356-1992
30
30
Support: Support.Eccotemp.com Shop Online: www.Eccotemp.com Phone: 866-356-1992
PLEASE NOTE: SH12
-
A IS FOR INDOOR PERMANENT INSTALLATIONS ONLY. THIS MANUAL AND ALL ECCOTEMP CONTENT IS SUBJECTED TO CHANGE WITHOUT NOTICE.
PLEASE VISIT SUPPORT.ECCOTEMP.COM FOR MORE INFORMATION.
English
Output temperature of water can be regulated by the
following options: Remote control and Eccotemp
SMARTHOME mobile APP.
Safety factors should be considered when selecting the water
temperature setting of the water heater. The water heater was
set at 110°F before it was shipped from the factory. This is the
recommended starting point.
Water temperatures above 120°F can cause severe burns or
death from scalding. The thermostat is adjusted to its lowest
temperature position when shipped from the factory.
Be sure to read and follow the warnings outlined in this
manual and on the label located on the water heater. Mixing values are available for reducing point of use water
temperature by mixing hot and cold water in branch water lines.
Procedures for adjusting the thermostat for energy ecient operation at the minimum water temperature setting
consistent with the consumer’s needs.
Contact a licensed plumber or the local plumbing authority for further information. See page 4 for details.
DANGER! There is a hot water scald potential if the temperature is set too high. Households with small
children, disabled, or elderly persons may require a 120°F or lower temperature setting to prevent contact
with HOT water.
PRESET TEMPERATURE:
The Eccotemp SHLX-LP/NG models are AUTOMATIC TEMPERATURE
CONTROLLED water heaters. Select one of the preset
temperatures on the SHLX by using the Eccotemp SMARTHOME
mobile app, and then adjust your sink/shower water temperature
at the source/faucet.
The following preset temperatures are:
LOW - 95°F / COMFORT - 120°F
HIGH - 130°F / COMMERCIAL - 140°F
The SHLX is a flow activated water heater and should maintain at
least 0.7 GPM to activate and 0.6 GPM to maintain activation.
AUTOMATIC VS. MANUAL TEMPERATURE CONTROL
The SHLX is an automatic temperature controlled tankless water
heater. Below explains the differences between an automatic and
manual temperature controlled tankless water heater. For
additional questions please visit support.eccotemp.com.
Operating Instructions
WATER TEMPERATURE SETTING
!
Turn water heater
ON/OFF
Press the power icon for 5 seconds to get
into EZ connection mode (fast blink) and
hold down for another 5 seconds to get
into AP connection mode (slow blink) that
produces a WiFi hotspot to connect to.
WARNING! Should overheating occur or the gas supply fail to shut o, turn o the manual gas control
valve to the water heater.
AUTOMATIC TEMPERATURE CONTROL:
The water heater will self-adjust temperature
according to what is being requested at the output
water source (sink or shower). It also will regulate
the temperature automatically according to how
many applications are being used at the same time.
Temperature doesn’t have to be reset after each use.
MANUAL TEMPERATURE CONTROL:
You must adjust the temperature manually each time
you use the water heater. The temperature must be
adjusted according to the amount of applications
being used at the same time due to the uctuation of
pressure.
NOTICE! If inlet water temperature is too high,
and set temperature is low, the actual temperature
might be higher than the set temperature, and
vice versa.
!
Time / Temperature Relationship in Scales
Water Temperature Time to Product a serious Burn
120 More than 5 minutes
125 1 1/2 to 2 minutes
130 About 30 seconds
135 About 10 seconds
140 Less than 5 seconds
145 Less than 3 seconds
150 About 1 1/2 seconds
155 About 1 second
Table courtesy of Shriners Burn Institute
To Next Page
Loading...
Need help?
General
