EasyManua.ls Logo

Echo GT-201R - User Manual

Echo GT-201R
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
X7712271301
X771000111
05/06
- START KIT P/N 99944200001
INSTALLATION/OPERATING INSTRUCTIONS
For Models: GT-200R/201R, SRM-210/211, SRM-210U/211U,
PE-200/201, SHC-210/211, PPF-210/211
If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an Echo
Service Dealer for installation of this kit. To help you decide whether you want to DO-IT-YOURSELF or have an
Echo dealer install this kit, we have rated this procedure as a SKILL LEVEL 2, which means some mechanical
experience and basic knowledge in the use of hand tools is necessary.
The Echo I-Start system is a starter accessory that will make your Echo unit easier to start by reducing the
pulling force by 75%.
If after reading these instructions, you are not sure of your ability to safely complete the installation, Echo
recommends you return the unit to your Echo dealer for service.
NOTE:
Carefully follow all assembly instructions,
in sequence, in order to avoid damage to the I-Start compo-
nents.
Tools Needed: 13mm Socket and Ratchet, Spark Plug Wrench, Cross Head Screwdriver, 3mm Hex Wrench,
Pliers, 3 X 1/4 in. Plastic Dowel Piston Stop similar to tooth brush handle (Recommended
Echo Piston Stop Part Number 91017).
Contents: i - Start Assembly, Two Pawl Catcher, Starter Spacer, 3-Tapping Screws, Engine Stand, Eye
Plate, Instruction Sheet
INSTALLATION
DISASSEMBLY:
1. Move stop switch to stop position.
2. Disconnect spark plug lead and remove spark plug with
spark plug wrench.
3. Remove four (4) starter screws with 3mm hex wrench,
turning counter clockwise (CCW). Retain screws for
reassembly.
NOTE:
Starter screws have thread lock compound and may be
difficult to remove. To prevent damaging screws, turn screws
½ turn CCW then ¼ turn clockwise (CW). Repeat procedure
until screws are removed.
4. Lift starter assembly from engine.
5. Insert piston stop into spark plug hole. Rotate pawl catcher
CCW until piston rests firmly against piston stop preventing
crankshaft from further rotation.
6. Use 13mm socket to remove pawl catcher from crankshaft,
turning CCW.

Table of Contents

Questions and Answers

  • S
    stephen36Aug 11, 2025
    Why is my Echo GT-201R Trimmer hard to start?
    • M
      Mark SwansonAug 11, 2025
      There are several reasons why your Echo Trimmer might be hard to start. It could be due to a clogged fuel strainer or fuel line, which you should clean or replace. Alternatively, the fuel mixture might be too rich; in this case, open the choke, clean or replace the air filter, or adjust the carburetor. Ensure the stop switch is turned to ON. Also check the spark plug gap and adjust it to 0.65mm (0.026in.), or clean/replace the spark plug if it's covered with carbon or fouled with fuel. If the problem persists, it could be an electrical problem, interlock switch issue or carburetor problem, and you should seek assistance from your Echo dealer.
  • K
    Katherine ThompsonAug 17, 2025
    Why my Echo GT-201R Trimmer engine cranks but won't start?
    • A
      Andrew SteinAug 17, 2025
      If your Echo Trimmer engine cranks but struggles to start or doesn't start at all, here are some potential causes: * A clogged fuel strainer or fuel line: In this case, you should clean or replace the affected component. * A fuel mixture that's too rich: Open the choke. * A muffler wet with fuel: Clean or replace the air filter; also, adjust the carburetor. * No spark: Turn the switch to the ON position, adjust to 0.65mm (0.026in.), clean or replace the spark plug, or replace the spark plug. For carburetor issues, no fuel at the cylinder, electrical problems, or interlock switch malfunctions, it's best to consult your Echo dealer.
  • L
    Leroy KnightAug 23, 2025
    Why my Echo GT-201R engine cranks but doesn't start?
    • M
      Mark PalmerAug 23, 2025
      If your Echo Trimmer engine cranks but doesn't start, the fuel strainer or fuel line might be clogged. Try cleaning or replacing them. Other potential issues could involve the carburetor, fuel at the cylinder, or a muffler wet with fuel, requiring you to open the choke, clean/replace the air filter or adjust the carburetor. Spark issues at the end of the plug wire or at the plug itself might also be the cause. In such cases, turn the switch to the ON position, adjust the spark plug to .65mm (0.026in.), clean or replace it.
  • K
    Kathleen BirdAug 29, 2025
    What to do if my Echo GT-201R Trimmer engine runs, but dies?
    • S
      Scott MortonAug 29, 2025
      If your Echo Trimmer engine runs but dies or does not accelerate properly, several factors could be responsible. A dirty air filter, fuel filter, or a plugged fuel vent can cause these issues; clean or replace these components as needed. Also, a dirty or worn spark plug can be the culprit; clean, adjust, or replace it. Improper carburetor adjustment or a dirty/plugged cooling system might also be the cause, so adjust the carburetor and clean the cooling system. Finally, a plugged spark arrestor screen can lead to these symptoms, so replace it.
  • A
    Amy HuangSep 4, 2025
    What to do if Echo GT-201R Trimmer engine runs, but dies or does not accelerate properly?
    • E
      Emily HenrySep 4, 2025
      If your Echo Trimmer engine runs but dies or doesn't accelerate properly, consider these possibilities: * A dirty air filter: Clean or replace it. * A dirty fuel filter: Replace it. * A plugged fuel vent: Clean or replace it. * A dirty or worn spark plug: Clean and adjust, or replace it. * Improper adjustment: Adjust the trimmer. * A dirty or plugged cooling system: Clean it. * A plugged spark arrestor screen: Replace it.

Echo GT-201R Specifications

General IconGeneral
BrandEcho
ModelGT-201R
CategoryTrimmer
LanguageEnglish

Related product manuals