USERINSTRUCTIONS
Beforestartingthemotor
• Makesurethattheoillevelisnotbelowminimum:Unscrewthecap(fig.1no.11),usearagtocleanthedipstick
andscrewthecapbackon.Unscrewthecapagainandcheckwhethertheoillevelfallswithintheminimumand
maximumlevelsindicated.Iftheoillevelisbelowminimum,addmoreoiluntilasuitablelevelisreached.(aska
trusteds
upplie
rforasuitableoiltypology).
ATTENTION!!! THEMOTOROILDOESNOTCOMESUPPLIEDWITHTHEMACHINE
• Makesurethatallofthescrewsaretightenedproperly.
• Makesu
retha
talloftheleversareintheirneutralpositions(fig.1no.6/no.9).
• Cleantheairfilterofanyobstructions(seethemotor’smanual).
• Refuelthemachinethroughitsfilteredfuelopening.
• Openthefueltap(seethemotor’smanual).
• Ifthemotoriscold,thegast
hrottle(fig
.1no.3)mustbesettoitsSTARTposition.
• Pullthemotor’sstarterhandle(fig.1no.2)withforce.Beforeusingthemachine,waitforafewminutesinorder
toallowthemotortoreachitsproperoperatingtemperature.
BESURETOALSOFOLLOWTHEINSTRUCTIONSDESCRIBEDWITHINTHEMOT
O
R’SMANUAL.
Before initiating any work activities, position the cable upon thespool, adjust the machine’s cable laying depthand tie
thelooseend ofthecabletoapeg.Makesurethattherearenopeople,animalsorforeignobjectswithin15metresof
themachine.Startthemotorandwaitforittoreachitspr
operoperatingtemperat
urebeforebeginning.Bringthecutter
activation lever (fig.1 no.9) and the advancement activation lever (fig.1 no.1) to their working positions and begin
working. Use maximum caution while operating the machine. Be sure to carefully read the operation descriptions
providedbelow.Duringthesummer,orwheneveropera
t
ingupondryterrain,itisrecommendedtowatertheoperating
areaabundantlythedaybeforetheworkistobeperformed.
THEMACHINEMUSTBE SUBJECTEDTOATRAILSTAGE!THEBELTSWILLADJUSTDURINGTHEFIRSTHOUROFWORK.
MAKESURETHATTHETENS
IONADJUSTMENTSPR
INGSAREALWAYSWORKINGPROPERLY(fig.1no.4/no.5).
POSITIONINGTHECABLEUPONTHESPOOL
Given the various cable and spool typologies which are available on the market, it is recommended that the cable be
wounduponthesuppliedcablespool(fig.1no.10),usingtheappropriatehandleuponthespoolitself.Thiswillfacilitate
the cable loading operations. In order to guarantee proper unwinding (fig.2), it is important that the ca
ble be wound
uponthespoolinaclockwisedirection.Iftheusershouldwanttouseaspoolwithcablealreadywounduponit,theleft
handsideofthesuppliedcablespoolcanberemovedbylooseningthethreeknobs(fig.3)andbyslightlyturningth
eside
ofthespoolitself.Positionthenewspooloverthesuppliedspool’scentralcylinder,usinganyadaptorsasrequired,and
reattach the side which was previously removed. Be sure to tighten the fastening knobs properly. Once the cable has
beenproperly positioned uponthe spool, the loose end ofthe cable must beinsertedinto the appropriate tube(fig
.4)
untila
fewcentimetresofcablecomeoutthebottom.
1‐Removableplate
2‐Knob
Fig.2 Fig.3 Fig.4
INSTALLINGORREPLACINGTHECUTTER
Themachineisequippedwithamechanismwhichallowsforthecuttertobequicklyreplaced withouttheneedfortools
(fig.5). In order to install or replace a cutter, push the support (fig.6) upwards and extract the worn cutter, if already
present upon the support (fig.7). While keeping the support pressed upwards, inser
t the new cutt
er then release the
support.Aspringactionmechanismwillautomaticallyrepositionthesupportinitsoriginalposition,therebylockingthe
new cutter in place. If replacing a worn cutter during work activities, it may be necessary to clean any residual grass
and/orsoiloff ofthesupport.Makesurethatnodebrisen
t
ersthequickattachmentmechanismwhileinstallingthenew
cutter. It is nevertheless recommended to clean and lubricate the quick attachment mechanism frequently (see also
“CLEANINGTHECUTTERSUPPORT”).
Fig.5 Fig.6 Fig.7
To Next Page
Loading...