To Next PageTo Next PageHow to fix ECOWITT HP2551 Weather Station no WiFi connection?
To troubleshoot a missing WiFi connection, check the following: 1. Look for the WiFi signal strength symbol on the display. If wireless connectivity is successful and reporting to Wunderground.com, the WiFi icon will be displayed on the home page. 2. Ensure your modem WiFi settings are correct, including the network name, password, and security settings.
Why does my ECOWITT Weather Station temperature sensor reads too high in the day time?
If your temperature sensor reads too high during the day, make sure that the sensor array is not too close to heat generating sources or structures such as buildings, pavement, walls, or air conditioning units. You can also use the calibration feature to offset installation issues related to radiant heat sources.
What to do if ECOWITT Weather Station rain gauge reports rain when it is not raining?
An unstable mounting solution may cause the rain gauge to incorrectly register rainfall. Ensure you have a stable, level mounting solution.
Why is my ECOWITT HP2551 data not reporting to Wunderground.com?
There are several reasons why your data might not be reporting to Wunderground.com: 1. Double-check that your password is correct. It is the same password you use on Wunderground.com, and it cannot begin with a non-alphanumeric character. 2. Verify that your station ID is correct, paying close attention to the capitalization and avoiding mixing up the letter 'O' with the number '0'. 3. Ensure that the date and time are correct on the console to avoid reporting old data. 4. Confirm that your time zone is set properly. 5. Check your router firewall settings, as the console sends data via Port 80.
What to do if my ECOWITT HP2551 outdoor sensor array does not communicate to the display console?
The sensor array may have initiated properly and the data is registered by the console as invalid, and the console must be reset. To resolve this, press the reset button for 3 seconds to completely discharge the voltage. Then, remove the batteries and wait one minute while covering the solar panel to drain any remaining voltage. Finally, put the batteries back in and resync with the console by powering down and up the console with the sensor array about 10 feet away.
What to do if ECOWITT HP2551 Weather Station wireless remote (thermo-hygrometer) is not reporting in to console?
If the wireless remote is not reporting to the console and you see dashes on the display, consider these solutions: * Move the sensor assembly closer to the display console, keeping in mind that the maximum line of sight communication range is about 150m. * Install a fresh set of batteries in the remote sensor(s). * Ensure the remote sensors are not transmitting through solid metal or earth barriers. * Move the display console away from electrical noise generating devices like computers and TVs.
General| Display Type | LCD |
|---|---|
| Display Size | 5.5 inches |
| Outdoor Channels | 8 |
| Indoor Channels | 1 |
| Data Logging | Yes |
| Wireless Transmission | 433 MHz |
| Sensor Reporting Interval | 16 seconds |
| Wi-Fi Standard | 802.11 b/g/n |
| USB Port | Yes |
| Alarms | Yes |
| Sensors | Temperature, Humidity, Wind Speed, Wind Direction, Rainfall, UV, Solar Radiation |
| Temperature Measurement Range | -40°C to 60°C |
| Indoor Temperature Range | -10°C to 50°C |
| Humidity Range | 10% - 99% |
| Wind Speed Measurement Range | 0 to 50 m/s |
| Wind Direction | 360° |
| Rainfall Measurement Range | 0 to 9999 mm |
| Wireless Transmission Range | 100 m |
| Supported Cloud Services | Ecowitt Weather Cloud, Weather Underground, WeatherCloud |
| Connectivity | Wi-Fi |
| Power Supply (Console) | 5V DC |
| Power Supply (Outdoor Sensor) | 2x AA batteries |
| Weather Forecast | Yes |
Discusses risks of lightning strikes, proper grounding, and safe installation heights.
Lists all items included in the weather station package.
Describes the main console unit and its ports.
Details the indoor sensor unit and its display.
Explains the components of the outdoor sensor array.
Lists optional sensors that can be connected to the console.
Steps before installing the weather station, including tool requirements.
Guidelines for choosing an optimal location for the sensor array.
Steps for attaching mounting hardware to the sensor.
Procedure for attaching the wind vane to the sensor.
Steps for installing the wind speed cups.
How to attach the rain gauge funnel.
Instructions for inserting batteries into the outdoor sensor.
Guidance on mounting the complete outdoor sensor assembly.
Location and function of the reset button and LED.
Instructions for setting up the indoor sensor.
Steps to install batteries in the multi-channel sensor.
Recommendations for optimal placement of the indoor sensor.
Tips for ensuring reliable wireless signal between sensors and console.
Identifies various elements displayed on the console screen.
Steps for initial setup after powering on the console.
Explains the functions of the buttons around the display.
Details icons for temperature and humidity readings.
How to view and clear maximum and minimum recorded data.
Navigating and viewing historical sensor data.
How to access specific pages of historical data.
Displays historical data trends in graphical format.
Shows data from multiple sensors or optional sensors.
Adjusting the date, time, and time zone settings.
Configuring time, date, temperature, barometric, wind, rainfall, and solar units.
Renaming or registering multi-channel sensors.
Configuring backlight behavior and brightness.
Setting geographical coordinates for accurate sunrise/sunset times.
Connecting the console to online weather services.
Scanning for and connecting to Wi-Fi networks.
Setting the daily rain reset time.
Accessing calibration and sensor ID setup screens.
Lists parameters, types, defaults, and calibration sources.
Calibrating temperature readings against a reference.
Calibrating humidity readings.
Explains absolute vs. relative pressure and calibration.
Notes on wind speed sensitivity and installation constraints.
Information on solar radiation conversion factors.
Details on rain collector calibration and maintenance.
Process for re-registering the indoor sensor.
Procedures for re-registering the outdoor sensor.
Setting automatic clearing of max/min records.
Restoring the device to its default factory settings.
Deleting all recorded historical data.
Clearing only the maximum and minimum recorded values.
Copying historical data to an SD card.
Displays model, firmware, and hardware information.
Steps for cleaning the rain gauge funnel.
How to clean the solar radiation sensor and panel.
Guidance on replacing batteries and corrosion prevention.
Solutions for issues with the remote sensor not communicating.
Troubleshooting steps for missing data indicators.
Resolving problems with the outdoor sensor array not displaying data.
Identifying causes and solutions for high daytime temperature readings.
Addressing issues where absolute pressure differs from official stations.
Troubleshooting inaccurate rain reporting.
Steps to resolve issues with uploading data to Wunderground.com.
Steps to troubleshoot and establish a Wi-Fi connection.
Technical details for the outdoor sensor.
Technical details for the indoor sensor.
Information on power sources and battery requirements.
