ECS EX-OR HP2000 - HP2000 Introduction; Communicating with a Detector; Performing a Detector Download; Adjusting Time Delay Settings

Call 1300 306 136
www.ecs.net.au
COMMUNICATING WITH A DETECTOR
@$OWNLOADINGTHESETTINGSFROMADETECTORCOPIES
THECONTENTSOFTHEDETECTORSMEMORYONTOTHE
SCREENANDMEMORYOFTHEPROGRAMMER
Caution: ‘Uploading’ new settings into the
detector over-writes the memory of the
detector with a copy of the contents of the
screen of the programmer. Always download
information prior to commencing.
.OTE)FPROGRAMMEDINCORRECTLYREPEATSTEPS
BELOW
4OPERFORMAdownloadFROMADETECTOR
 #HECKTHATTHEPROGRAMMERISTURNED/.
&IG
 0OINTTHEPROGRAMMERATTHELENSOFTHE
DETECTORIDEALLYFROMDIRECTLYBELOWANDFROM
TOMETRESAWAY
 (OLDINGTHEPROGRAMMERSTEADYPRESS
ANDRELEASETHEDownload BUTTON&IG
#/.4).5%4/(/,$THEPROGRAMMERSTILL
WHILETHEPROGRAMMERANDDETECTOREXCHANGE
INFORMATIONTHISMAYTAKEUPTOSECONDS
)FTHELIGHTSCONTROLLEDBYTHEDETECTORARE@/.
PRIORTOADOWNLOADTHEYWILLSWITCHOFFFORA
FEWSECONDSWHILETHEDOWNLOADISOCCURRING
4HEDOWNLOADISCOMPLETEWHENTHE(0
DISPLAYSINFORMATIONFROMTHEDETECTOR&IG
 )FTHEEXCHANGEISBROKENOFFTYPICALLYDUE
TOTHEPROGRAMMERBEINGMOVEDTOOMUCH
THELIGHTSWILLNOTCOMEON3IMPLYREPEATTHE
PROCESSAFTERADJUSTINGTHEDISTANCEORAIMIF
NECESSARY
HP2000 INTRODUCTION
4HE%X/R(0$IGITAL0ROGRAMMER(ANDSETISDESIGNEDFORUSEWITH
%X/RSRANGEOFLIGHTINGCONTROLSYSTEMS4HEPROGRAMMABLEPARAMETERS
OFTHEVARIOUSPRODUCTSCANBECONlGUREDVIATHISBATTERYPOWEREDHAND
HELDINFRAREDUNIT
4HE(0ALLOWSCOMMISSIONINGANDRECOMMISSIONINGTOBECARRIED
OUTWITHVIRTUALLYNODISTURBANCETOTHEBUILDINGSOCCUPANTS3ETTINGS
ARECHOSENFROMTHE(0SMENUANDTRANSFERREDINSTANTANEOUSLY
TOTHEPRODUCTBEINGPROGRAMMEDBYPRESSINGTHE5PLOADBUTTON4HE
COMMISSIONINGENGINEERRECEIVESPOSITIVEFEEDBACKATALLSTAGESOFTHE
PROCESS3ETTINGSFROMONEPRODUCTCANBECOPIEDINSECONDSTOANOTHER
ANDSETTINGSCANBECHECKEDATANYTIMEUSINGTHE(0SDOWNLOAD
FUNCTION
2EPROGRAMMINGOFTHEPARAMETERSSETDURINGCOMMISSIONINGCANBE
CARRIEDOUTQUICKLYANDEASILYUSINGTHE(04HE(0CANBE
EASILYUPGRADEDTOACCOMMODATEPRODUCTREVISIONSADDITIONSBYTHE
SUPPLIED0#3OFTWAREPACKAGEVIA53"2EFERTOBACKPAGE
ADJUSTING TIME DELAY SETTINGS
 4OESTABLISHTHECURRENTSETTINGSOFADETECTOR
PERFORMA$OWNLOAD2EPEAT3TEPS
Note that this will not alter the settings in the detector.
This simply allows the settings within the detector to be
read on the screen of the programmer.
 5SETHE$/7.BUTTONTOGOTOTHENEXT
SCREENTHENSCROLL$/7.AGAINTOHIGHLIGHT
OFF DELAY&IGTHENPRESSOK
If information about this parameter is required, scroll UP
or DOWN to highlight HELP and press the OK button.
Press the Left arrow button to return to the previous
menu.
4HEEDIT PARAMETERSHOULDBE
HIGHLIGHTED&IG)FNOTSCROLLTOSELECTEDIT
PARAMETERTHENPRESSOK4HECURRENT
SETTINGWILLBEHIGHLIGHTED&IG
 3CROLL50OR$/7.TOSELECTTHEDESIREDTIME
DELAY4HENPRESSOK&IG
This will be the new OFF DELAY setting to control the
length of time the lights remain ON once movement is
no longer detected by the detector.
 5PLOADTHENEWSETTINGTOTHEDETECTORBY
SELECTINGTHEUPLOAD THIS ITEMOPTION
THENPRESSOK&IGASYOUPOINTTHE
(0DIRECTLYTOWARDSTHEDETECTOR
The lights will turn OFF then ON to acknowledge a
successful upload.
Battery Life
11
LCD Display
9
On / Off
1
Download
8
Upload
7
Scroll Up
5
OK
4
Forward
2
Scroll Down
6
Back
3
USB Port
10
Press the DOWNLOAD
button
FIGURE 2
Results
Data OK
MLS2000D
Ballast: DSI 1%
Power up unit by
pressing the ON button
FIGURE 1
MAIN MENU
LAST EDITED
CHANGE PRODUCT
UTILITIES
SETUP
ABOUT
POWER OFF PROGRAMMER
Press Down button to go
to the next screen, then
scroll to OFF DELAY.
FIGURE 3
MLS2000D
POWER UP: OFF
RESPONSE: AUTO
MINIMUM ON TIME: NO
OFF DELAY: 60 mins
BUS CONNECT: YES
1st ZONE: 29
%8/2(0
HAND-HELD PROGRAMMER
Select EDIT PARAMETER
then press OK.
FIGURE 4
OFF DELAY: 60 mins
EDIT PARAMETER
HELP
UPLOAD