Need help?Do you have a question about the Eden Navigator WP-100 and is the answer not in the manual?
Important safety warning regarding hearing protection and safe operating levels to prevent hearing loss.
Describes the input jack's function and signal level handling for direct connection to the preamplifier.
Explains how to set the relative gain level and match the input signal to the preamp's output.
Details the feature for adjusting tube-style distortion, from subtle soft asymmetry to pronounced sound.
Covers the tone preset for boosting bass/highs and cutting lower mids for a modern bass tone.
Allows the Enhance control to be switched on/off via panel or foot switch for quick tone changes.
LED indicator to optimize signal-to-noise ratio and maintain headroom by adjusting gain on loud notes.
Mutes all outputs for tuning, with the Tuner buss remaining live. Activated by panel or foot switch.
Enables switching the Compressor in/out via panel or foot switch. Red LED indicates bypass mode.
Details the dBx-style compressor with adjustable Ratio and Threshold for peak protection and headroom.
Provides a preset 10dB gain increase for solos and accents, controlled via foot switch.
Describes the EQ layout: Bass/Treble shelving filters and three adjustable semi-parametric filters.
A shelving filter for +/- 15 dB adjustment at 30 Hz, effective for 5, 6, 7 string instruments.
A shelving filter for +/- 15 dB adjustment of treble frequencies, flat at 12:00 position.
Explains quasi-parametric filters with fixed bandwidth, adjustable +/- 15 dB, flat at 12:00 position.
Boosts or cuts 15 dB from deep Bass (30Hz) to lower midrange (300 Hz).
Adjusts middle frequencies from 200 Hz to 2 KHz, +/- 15 dB, for cutting through the mix.
Operates in the 1.2KHz to 12 KHz range for bright top end sound.
Main D.I. output (+21 dBm), selectable between tube, post-compressor, or post-tone control.
Parallel effects loop with tone controls, allowing blended effects with return level adjustment.
Stereo line level input for mixing external sources like CD players or monitors.
Allows stereo configuration or engagement of the internal electronic crossover for bi-amping.
Adjustable crossover frequency from 120 Hz to 1.2 KHz with a Butterworth style filter.
Adjusts L/R balance in stereo or high/low balance in Bi-Amp mode for speaker level matching.
Final output control for Main and DI outputs, recommended setting for normal use is 9:00 to 12:00.
Displays actual output function calibrated to 0 dBm at full drive for specific amplifier inputs.
Engages internal stereo output limiters for amplifier protection, selectable for different voltage standards.
Jack for stereo headphones only. Warning against using mono signal sends to avoid damage.
Master power switch. Advised to turn Master Level down before turning unit on or off.
Mutes Main D.I.s (L/R), L/R 1/4" outputs, and Instrument D.I. during turn on/off.
DC powered indicators for power supply operation and illumination in low light conditions.
Details rear panel connectors and features like ground lifts and main outputs.
Separate ground lifts for D.I. sends to reduce hum and eliminate ground loops in complex systems.
Connect to power amplifiers, providing up to +21 dBm output without clipping.
Low impedance balanced outputs providing +16 dBm, post all effects and tone, without clipping.
Standard IEC connector. Fuse replacement guidelines and warning about internal AC connections.
True stereo line level inputs for CD players, ADATs, etc., front panel level controlled.
Discrete stereo loop post tone controls and pre-final outputs. Configured for line level operation.
Loop across tone controls for parallel operation of effects and EQs, with blended return level.
Mono send/return loop positioned prior to the tone control section at line level.
Direct output from vacuum tube, not muted during muting modes, allows continuous tuner connection.
Connects optional foot switch via standard 5-wire MIDI cable. LED lights follow panel lights.
Controlled on front panel for position/level, separate ground lift. Capable of +21 dBm.
Hands-free access to Mute, Enhance Bypass, Compressor Bypass, and Turbo Boost controls.
Instructions for voltage changes by authorized technician only, warning about safety and warranty.
Guide to setting controls flat to establish a baseline tone for adjustments.
Advice on creating great tone by working with the instrument's natural sound and using controls wisely.
Contact details for amplifier malfunction, questions, or authorized service center assistance.
Visual examples of EQ settings for tone shaping, showing knob positions for different sounds.
Provides address, phone numbers, fax, email, and website for Eden Electronics.
Specific address and contact information for shipping authorized returns for service.
To Next Page
General