Edge-Core ECS4100-28T

To Next Page

– 1 –

Quick Start Guide

1. Unpack the Switch and Check Contents

ECS4100-26TX

ECS4100-26TX-ME

ECS4100-28T

ECS4100-52T

Rack Mounting Kit—two brackets and eight screws

Four adhesive foot pads

Power Cord—either Japan, US, Continental Europe

or UK

Console Cable—RJ-45 to DB-9

Documentation—Quick Start Guide (this document)

and Safety and Regulatory Information

Note:

The ECS4100 series switches are for indoor use only.

Note:

For Safety and Regulatory information, refer to the

Safety and Regulatory Information document included with

the switch.

Note:

Other documentation, including the Installation

Guide, Web Management Guide, and CLI Reference Guide,

can be obtained from www.edge-core.com.

2. Mount the Switch

Attach the brackets to the switch.

Use the screws and cage nuts supplied with the rack to

secure the switch in the rack.

Caution:

Installing the switch in a rack requires two

people. One person should position the switch in the rack,

while the other secures it using the rack screws.

Note:

The switch can also be installed on a desktop or shelf

using the included adhesive rubber foot pads.

3. Ground the Switch

Ensure the rack on which the switch is to be mounted is

properly grounded and in compliance with ETSI ETS 300 253.

Verify that there is a good electrical connection to the

grounding point on the rack (no paint or isolating surface

treatment).

Attach a lug (not provided) to a #12 AWG (PoE switch) or #18

AWG (non-PoE switch) minimum grounding wire (not

provided), and connect it to the grounding point on the

switch using 3.5 mm screw with washer. Then connect the

other end of the wire to rack ground.

Caution

The earth connection must not be removed

unless all supply connections have been disconnected.

Caution:

The device must be installed in a restricted-access

location. It should have a separate protective earthing

terminal on the chassis that must be permanently

connected to earth to adequately ground the chassis and

protect the operator from electrical hazards.

4. Connect Power

a. Connect AC Power

Plug the AC power cord into the socket on the rear of the

switch.

Connect the other end of the power cord to an AC power

source. Verify that the external AC power requirements for

the switch can be met as listed below:

ECS4100-26TX: AC 100-240 V, 50/60 Hz, 1 A

ECS4100-28T: AC 100-240 V, 50/60 Hz, 1 A

ECS4100-52T: AC 100-240 V, 50/60 Hz,1 A

Note:

For International use, you may need to change the AC

line cord. You must use a line cord set that has been

approved for the socket type in your country.

E012017-AP-R02

150200001586A

www.edge-core.com

26-Port L2+ 10G Ethernet Switch (ECS4100-26TX/ECS4100-26TX-ME)

52-Port L2+ Gigabit Ethernet Switch (ECS4100-52T)

28-Port L2+ Gigabit Ethernet Switch (ECS4100-28T)

Need help?

Do you have a question about the Edge-Core ECS4100-28T and is the answer not in the manual?

Edge-Core ECS4100-28T Specifications

General

Model	ECS4100-28T
Ports	24 x 10/100/1000BASE-T, 4 x 1G SFP
Switching Capacity	56 Gbps
Forwarding Rate	41.7 Mpps
MAC Address Table Size	16K
Jumbo Frame Support	9KB
Weight	3.5 kg
Storage Humidity	5% to 95% (non-condensing)
VLANs	4K
Power Supply	AC 100-240V, 50/60Hz
Dimensions (W x D x H)	440 x 44 x mm
Operating Temperature	0 to 45 °C
Storage Temperature	-40 to 70 °C
Standards Compliance	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.1Q, IEEE 802.1p
Operating Humidity	10% to 90% (non-condensing)