Edge-Core ECS4620-28F-2AC User Manual

– 1 –
1. Unpack the Device and Check Contents
ECS4620-28T
ECS4620-28P
ECS4620-28F
ECS4620-52T
ECS4620-52P
ECS4620-28T-DC
ECS4620-28F-DC
ECS4620-28F-2AC
ECS4620-52P-2AC
Rack Mounting Kit—two brackets and eight screws
Four adhesive foot pads
Power Cord—either Japan, US, Continental Europe
or UK
Console Cable—RJ-45 to DB-9
DC connector plug (ECS4620-28T-DC and ECS4620-
28F-DC only)
Documentation—Quick Start Guide (this document)
and Safety and Regulatory Information
Note: The ECS4620 series switches are for indoor use only.
Note: For Safety and Regulatory information, refer to
the
Safety and Regulatory Information document
included with the device.
Note: Other documentation, including the
Installation Guide, Web Management Guide, and CLI
Reference Guide, can be obtained from
www.edge-
core.com
.
2. Mount the Device
Attach the brackets to the device.
Use the screws and cage nuts supplied with the rack to
secure the device in the rack.
Caution: Installing the device in a rack requires two people.
One person should position the device in the rack, while the
other secures it using the rack screws.
Attention: L’installation du commutateur dans un rack
nécessite deux personnes. Une personne doit positionner le
commutateur dans le rack, tandis que l’autre le fixe à l’aide
des vis de montage.
Note: The device can also be installed on a desktop or shelf
using the included adhesive rubber foot pads.
3. Ground the Device
Ensure the rack on which the device is to be mounted is
properly grounded and in compliance with ETSI ETS 300 253.
Verify that there is a good electrical connection to the
grounding point on the rack (no paint or isolating surface
treatment).
2
1
1
2
1
1
28/52-Port L3 Gigabit Ethernet Stackable Switch
ECS4620-28T | ECS4620-28P | ECS4620-28F | ECS4620-52T | ECS4620-52P
ECS4620-28T-DC | ECS4620-28F-DC | ECS4620-52P-2AC | ECS4620-28F-2AC
Quick Start Guide
E122022-AP-R05
150200001752A
*150200001752A_R05*

Edge-Core ECS4620-28F-2AC Specifications

General

Model	ECS4620-28F-2AC
Ports	28
SFP Ports	24
Power over Ethernet (PoE)	No
Switching Capacity	128 Gbps
Forwarding Rate	95.2 Mpps
Layer	L2/L3
MAC Address Table Size	16K
VLANs	4K
Weight	3.5 kg
Operating Temperature	0°C to 50°C
Storage Temperature	-40°C to 70°C
Type	Switch
10G SFP+ Ports	4
Power Supply	AC: 100~240VAC, 50/60 Hz
Humidity	10% to 90% (non-condensing)
Standards Compliance	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x, IEEE 802.1Q, IEEE 802.1P, IEEE 802.1D, IEEE 802.1S, IEEE 802.1W

Summary

Unpack and Check Device Contents

Mount the Device

Desktop or Shelf Mounting

Alternative mounting option using adhesive rubber foot pads.

Ground the Device

Connect Power

Connect AC Power

Procedure for connecting the device to an AC power source using power cords.

Connect DC Power

Procedure for connecting the device to a DC power source.

Verify Device Operation

Perform Initial Configuration

Connect PC to Console Port

Connect a PC to the device console port using a console cable.

Configure PC Serial Port

Configure PC serial port settings for console connection.

Log in to CLI

Log in to the device's Command Line Interface using default credentials.

Connect Network Cables

Connect RJ-45 Cables

Connect Category 5, 5e, or better twisted-pair cables to RJ-45 ports.

Connect SFP/SFP+ Transceivers

Install SFP/SFP+ transceivers and connect fiber optic cabling.

Check Port Status LEDs

Verify link status and PoE activity using port status LEDs.

Hardware Specifications

Device Chassis Specifications

Details on device size, weight, operating temperature, and humidity.

Power Specifications

Information on AC input, DC input, total power consumption, and PoE budget.

Regulatory Compliances

List of certifications including CE, FCC, VCCI, BSMI, UL, IEC, and RoHS.