Edge-Core ECS4100-12T

– 1 –
1. Unpack the Switch and Check Contents
ECS4100-12T
ECS4100-12PH
ECS4100-28TC
ECS4100-26TX
ECS4100-26TX-ME
ECS4100-28T
ECS4100-28P
ECS4100-52T
ECS4100-52P
Rack Mounting Kit—two brackets and eight screws
Four adhesive foot pads
Power Cord—either Japan, US, Continental Europe
or UK
Console Cable—RJ-45 to DB-9
Documentation—Quick Start Guide (this document)
and Safety and Regulatory Information
Note: The ECS4100 series switches are for indoor use only.
Note: For safety and regulatory information, refer to the
Safety and Regulatory Information document included with
the switch.
Note: Other documentation, including the Web
Management Guide, and CLI Reference Guide, can be
obtained from www.edge-core.com.
2. Mount the Switch
Attach the brackets to the switch.
Use the screws and cage nuts supplied with the rack to
secure the switch in the rack.
Caution: Installing the switch in a rack requires two
people. One person should position the switch in the rack,
while the other secures it using the rack screws.
Note: The switch can also be installed on a desktop or shelf
using the included adhesive rubber foot pads.
3. Ground the Switch
Ensure the rack on which the switch is to be mounted is
properly grounded and in compliance with ETSI ETS 300 253.
Verify that there is a good electrical connection to the
grounding point on the rack (no paint or isolating surface
treatment).
Attach a lug (not provided) to a #18 AWG minimum
grounding wire (not provided), and connect it to the
grounding point on the switch using a 3.5 mm screw and
washer. Then connect the other end of the wire to rack
ground.
Caution: The earth connection must not be removed
unless all supply connections have been disconnected.
Caution: The device must be installed in a restricted-access
location. It should have a separate protective earthing
terminal on the chassis that must be permanently
connected to earth to adequately ground the chassis and
protect the operator from electrical hazards.
2
1
1
2
1
2
1
2
E042018-KS-R01
150200001807A www.edge-core.com
ECS4100 Series Switch
Quick Start Guide

Edge-Core ECS4100-12T Specifications

General

Brand	Edge-Core
Model	ECS4100-12T
Category	Switch
Language	English

Summary

Unpack the Switch and Check Contents

Included Items

Mount the Switch

Rack Mounting Instructions

Ground the Switch

Rack Grounding Compliance

Ensures the rack is properly grounded and compliant with ETSI ETS 300 253 for electrical safety.

Rack Grounding Verification

Ensures the rack is properly grounded per ETSI ETS 300 253 and has good electrical conductivity.

Grounding Wire Connection

Connects an #18 AWG grounding wire to the switch and the rack ground point.

Grounding Wire Installation

Connects an #18 AWG grounding wire to the switch and the rack ground point.

Grounding Safety Precautions

Cautions against removing grounding before power disconnection and highlights the need for permanent chassis grounding.

Grounding Safety Warnings

Connect Power

AC Power Connection

DC Power Connection for ECS4100-26 TX-ME

Perform Initial Configuration

Console Connection and Setup

Steps for connecting a PC to the console port and configuring the PC's serial port settings.

Connect Network Cables

RJ-45 Port Cabling

Guidance on connecting 100-ohm Category 5, 5e, or better twisted-pair cables to RJ-45 ports.

RJ-45 Cable Connection

Connects 100-ohm Category 5, 5e, or better twisted-pair cables to RJ-45 ports.

SFPSFP+ Port Cabling

Instructions for installing transceivers and connecting fiber optic cabling to SFP/SFP+ slots.

SFPSFP+ Transceiver and Fiber Cabling

Installs SFP/SFP+ transceivers and connects fiber optic cabling, listing supported transceiver types.

Port Status LED Interpretation

Port Status LED Indicators

Install the Switch

Rack Mounting Procedure

Initial Configuration

Console Setup and PC Configuration

Connects PC to console port and configures serial port settings (115200 bps, 8-N-1).

CLI Login Credentials

Login using default credentials: username 'admin', password 'admin'.

CLI Login

Login using default credentials: username 'admin', password 'admin'.