EDI 2010ECL User Manual

THIS MANUAL CONTAINS TECHNICAL INFORMATION FOR THE FOLLOWING SERIES
OF MODEL 210/2010/2018 SIGNAL MONITORS, PCB Issue G:
210E, 210ECL, 2010, 2010ECL, 2010ECLip, 2018ECL, 2018ECLip
REVISION: NOVEMBER 2014
pn 888-2010-002
- NOTE -
EDI ECCOM SOFTWARE MUST BE UPDATED TO VERSION 3.8.0 OR
GREATER FOR COMPATIBILITY WITH THIS FIRMWARE VERSION.
THE ECCOM SOFTWARE IS AVAILABLE FREE OF CHARGE AT
WWW.EDITRAFFIC.COM
210E - 210ECL - 2010ECL - 2018ECL
RMS Signal Monitor
Operations Manual

EDI 2010ECL Specifications

General

Brand	EDI
Model	2010ECL
Category	Measuring Instruments
Language	English

Summary

Section 1 Basic Functions

1.2 Basic Functions

Details fundamental operations like conflict monitoring, 24VDC, and watchdog monitoring.

Section 2 Extended Features

2.2 Red Failure Monitoring

Explains monitoring for absence of red signal and associated fault conditions.

2.3 GYR-Dual Indication Monitoring

2.4 Clearance (Short or Absent Yellow) Monitoring

2.5 AC Line Brown-out Detection

Explains detection of low AC line voltage conditions and their impact.

2.7 Recurrent Pulse Detection

2.12 Internal MPU Watchdog

2.18 Diagnostic Display Mode (210E / 2010)

Displays real-time and historical fault status for 210E/2010 models.

2.19 Diagnostic Display Mode (210ECL / 2010ECL /2018ECL)

Displays real-time and historical fault status for ECL models.

2.20 Flashing Yellow Arrow (FYA) Overview

Overview of monitoring for Flashing Yellow Arrow (FYA) signal displays.

Section 3 Event Logging Features

3.1 Basic Front Panel Fault Event Display

3.2 Model 210ECL / 2010ECL /2018ECL Status/Event Reporting

Details communication of status and event data via serial or Ethernet.

3.2.2 EDI ECcom Monitor Report

Describes interaction with EDI ECcom software for status and logs.

Section 4 Installation

4.1 Adapting Red Monitoring

Steps to adapt the monitor for Red Signal Monitoring using adapter PCB.

4.1.1 Red Field Inputs

4.1.2 Special Function Preempt Inputs (SF1, SF2)

4.2 SSM Switch Programming

4.3 Program Card Programming

Describes assigning non-conflicting channels using the program card.

4.4 Option Switch Programming

Details various monitor operations configurable via option switches (SW3).

4.5 Select Jumper Programming

Describes jumper options for configuring monitor operation.

4.5.1 Watchdog Latch Select (SEL1)

4.5.5 AC Line Brown-out Select (SEL5)

4.6 Watchdog Programming

Section 5 Front Panel Description

5.1 Indicators

Describes the function of each front panel LED indicator.

5.2 Front Panel Controls

Section 8 Specifications

8.1 Electrical

Lists electrical specifications including voltage, frequency, power, and AC/DC monitors.

8.1.1 Power Requirements

Specifies operating line voltage, frequency, and power consumption.

8.1.2 AC Voltage Monitors

Details voltage monitoring thresholds for various AC signal inputs.

8.1.3 DC Voltage Monitors

8.1.4 Outputs

8.2 Timing Functions

Lists various timing parameters for fault detection and operation.

Section 9 Wiring Assignments

9.1 Monitor Unit Connector (P6)

Details pin assignments for the main monitor unit connector.

9.1.1 Sixteen Channel

Pin assignments for the 16-channel configuration of the P6 connector.

9.1.2 Eighteen Channel

Pin assignments for the 18-channel configuration of the P6 connector.

9.2 Program Card Connector

Details pin assignments for the program card connector.

9.2.1 Sixteen Channel

9.2.2 Eighteen Channel

9.3 Red Interface Connector (P1)

Details pin assignments and function of the Red Interface connector.

9.4 EIA-232 Connector (J1)

Details pin assignments for the EIA-232 serial communication connector.

9.4.1 EIA-232 Cable to a PC

9.4.2 EIA-232 Cable to a 170 Controller Unit

9.5 Ethernet LAN Port

Details configuration and connection requirements for the Ethernet port.

9.6 16-Channel Program Card Diagram