EDIFIER QR65 User Manual

2. What’s in the Box?
3. Product oveiew
5. Power on/o
7. Control
8. Indicator status
9. Charge external devices
10. Know more about this speaker
6. Audio inputs
11. Specications
12. Troubleshooting
4. Cable connection
Total output power: R/L(Treble): 15W+15W, R/L(Mid-Bass): 20W+20W
Charging output power: 65W max.
Frequency response: 55Hz-40kHz
Declaration for EU
Frequency Band: 2.402GHz ~ 2.480GHz
RF Power Output: ≤12 dBm (EIRP)
There is no restriction of use.
Manual
Cannot connect to your Bluetooth device
• Make sure that the distance between this product and your Bluetooth device
is less than 10 meters and there are no obstacles between them.
• Make sure that no device is connected to this product via Bluetooth.
• Make sure that this product is in Bluetooth pairing mode. If not, manually
switch it to this mode.
• Resta this product, enable Bluetooth function on your Bluetooth device,
and then t again.
• Reset this product to facto settings and t again.
No power
• Make sure that the power cable is properly connected.
• Make sure that the power supply is not disconnected.
• Make sure that the main power button on the rear panel is switched to "ON".
No sound
• Make sure that this product is powered on.
• Make sure that this product and your device is properly connected.
• Make sure that the playback is not paused.
• Make sure that this product and your device are not muted.
• Increase the volume of this product and your device.
Noise coming from speakers
• EDIFIER speakers generate little noise, while the background noise of some
audio devices are too high. Please unplug audio cables and turn the volume
up. If no sound can be heard at 1 meter away from the speaker, there is no
problem with this product.
To learn more about EDIFIER, please visit www.edier.com
For EDIFIER warranty queries, please visit the relevant count page on
www.edier.com and review the section titled Warranty Terms.
USA and Canada: seice@edier.ca
South America: Please visit www.edier.com (English) or
www.edierla.com (Spanish/Pouguese) for local contact information.
Multimedia Speaker
QR65
Note:
•Images are for illustrative purposes only and may dier from the actual product.
•The bundled USB connecting cable is for audio streaming only. Do not use it for
device charging.
•For the need of technical improvement and system upgrade, information and
specications contained herein may be slightly dierent from actual product.
If any dierence is found, the actual product prevails.
•Switch input modes,
•Control play in Bluetooth mode and USB audio streaming mode,
•Select or customize EQs,
•Select or customize light eects,
•Upgrade the rmware, and
•More functions.
Passive speaker Active speaker
Quick sta guide
Impoant safety
instruction
Cleaning cloth
3.5mm to RCA audio cable
USB connecting cable
Speaker connecting cable
Power cable Speaker stands
Rear view of active speaker
●
EN
1. EDIFIER ConneX app
With this app, you can
Rear view of passive speaker
●
LINE IN input
USB audio
streaming input
Subwoofer output
USB-C 2 charging output
po
Connect to the
passive speaker
Power switch
Power cable
connector
USB-A charging output
po
USB-C 1 charging output
po
Connect to the active
speaker
Side view of active speaker
●
Press and hold: Switch to standby mode (in work mode)
Press: Switch input modes (in work mode)
Switch to work mode (in standby mode)
Rotate: Rotate clockwise to increase volume.
Rotate counterclockwise to decrease volume.
In LINE IN mode, rotate to unmute the speaker.
Press: Play/pause (in USB audio streaming or Bluetooth mode)
Mute/unmute the speaker (in LINE IN mode)
Press and hold: Disconnect Bluetooth (in Bluetooth mode)
Switch to Bluetooth pairing mode (in Bluetooth
hidden mode)
Rotate: Rotate clockwise to increase light brightness.
Rotate counterclockwise to decrease light brightness.
Press: Switch light eects.
Press and hold: Reset to facto settings.
Blue: Bluetooth input
Red: USB audio streaming input
Green: LINE IN input
ON
*
1. Connect the active and passive speakers using the speaker connecting cable.
2. Connect your device and the active speaker properly. To connect it with a
subwoofer, another suitable audio cable may be required.
3. Connect to a power source using the power cable, and then turn on the power
switch.
* This plug type is meant for illustration purpose only.
Input: 100-240V~ 50/60Hz 1.5A
(not included)
Power on: Switch the main power button on the rear panel of the active speaker to
"ON".
Power o: Switch the main power button to "OFF".
1. When the speaker is powered on for the rst time, it will auto-enter Bluetooth mode.
2. You can also press the " " button to switch to Bluetooth mode manually (blue
LED blinking rapidly), and the speaker will enter Bluetooth pairing mode.
3. Select "EDIFIER QR65" in your device setting to connect, and the blue LED will be
steady lit when the connection is established.
• To disconnect from the current Bluetooth device, press and hold the "
VOLUME "
button for 1.5 seconds.
Note:
1. Pin code for connection is "0000" if needed.
2. To enjoy all Bluetooth functions of this product, make sure that your audio source
device suppos A2DP and AVRCP proles.
3. If no device is connected in 30 minutes, the speaker will switch to Bluetooth hidden
mode. In this mode, (1) new devices cannot nd the speaker, but (2) for a device
that exists in the pairing record of this speaker, you can select "EDIFIER QR65" from
its Bluetooth device list to reconnect. To exit from Bluetooth hidden mode, press
and hold the "
VOLUME " button for 1.5 seconds.
Bluetooth input
●
Bluetooth
Settings
EDIFIER QR65
DEVICES
Bluetooth
2:12
Press
1. Press the " " button to switch to LINE IN mode (Green LED).
2. Connect your device to the LINE IN input pos (note color matching) with the
3.5mm to RCA audio cable.
3. Play audio and control the playback on your device.
Note:
In LINE IN mode, volume sync is not suppoed. To adjust the volume, adjust on the
speaker and your device separately.
LINE IN input
●
Press Green
USB audio streaming input
●
Press Red
Note:
•Power input: 100-240V~ 50/60Hz 1.5A
•During charging, make sure that the power cable is properly connected and the
main power button on the rear panel of the active speaker is switched to "ON".
•To guarantee high-eciency charging, use a charging cable that suppos the
charging current of 4.5A or higher.
Connect your device to the USB-A po, USB-C 1 po or USB-C 2 po on the rear
panel of the active speaker for charging.
ON
Get the latest rmware
Upgrade the rmware when a version update notice appears in your EDIFIER
ConneX app. During upgrading, the LED on the side panel of the active speaker
will blink in red, blue and green.
Note: Do not disconnect the power supply and Bluetooth connection during
upgrading.
How to reset this speaker to facto settings?
In work mode, press and hold the "
LIGHT EFFECTS " button for 5 seconds.
Note: After the speaker is reset, all settings and pairing records on the speaker will
be cleared.
Button / Knob Mode Action
Work mode
Press and hold to switch to standby mode.
Standby mode Press to switch to work mode.
Work mode Press to switch input modes.
Work mode Rotate clockwise to increase volume.
Work mode
Rotate counterclockwise to decrease
volume.
LINE IN mode Press to mute or unmute the speaker.
LINE IN mode Rotate to unmute the speaker.
Indicator status Speaker status
Blinking in blue per 0.2s Bluetooth pairing mode
Blinking in blue per 0.5s Bluetooth hidden mode
Solid blue Bluetooth device connected
Solid green LINE IN mode
Solid red USB audio streaming mode
Blinking in green Muted in LINE IN mode
Blinking in red, blue and green Upgrading the rmware
USB audio
streaming or
Bluetooth mode
Press to pause or resume the current track.
Bluetooth device
connected
Press and hold to disconnect the current
Bluetooth device.
Bluetooth hidden
mode
Press and hold to exit from Bluetooth hidden
mode and enter Bluetooth pairing mode.
Work mode Rotate clockwise to increase light brightness.
Work mode
Rotate counterclockwise to decrease light
brightness.
Work mode Press to switch light eects.
Work mode Press and hold to reset to facto settings.
USB-A 5V 3A, 9V 3A, 12V 3A, 20V 3A (60W max.)
USB-C 1 5V 3A, 9V 3A, 12V 3A, 15V 3A, 20V 3.25A (65W max.)
USB-C 2 5V 3A, 9V 3A, 12V 3A, 15V 3A, 20V 3.25A (65W max.)
USB-C 1 and USB-C 2 20W max. + 45W max.
USB-A and USB-C 1 15W max.
USB-A and USB-C 2 20W max. + 45W max.
USB-A, USB-C 1
and USB-C 2
15W max. + 45W max.
1. Press the " " button to switch to USB audio streaming mode (Red LED).
2. Connect the speaker to your computer with the bundled USB connecting cable.
3. On the computer, open the sound settings and select "EDIFIER QR65" as its output
device.
Note:
1. In USB audio streaming mode, volume sync is not suppoed. To adjust the volume,
adjust on the speaker and your computer separately.
2. The following operating systems suppo USB audio streaming: Windows 11,
Windows 10, Windows 8, and Windows 7.

EDIFIER QR65 Specifications

General

Brand	EDIFIER
Model	QR65
Category	Speakers
Language	English