56V LITHIUM-ION PRESSURE WASHER — HPW2000E10
a. Remove the nozzle.
b. Press the trigger and wait until a steady water
stream starts coming out of the wand.
c. Release the trigger and re-install the nozzle.
To Stop the Pressure Washer
1. Once the washing is completed, release the trigger
and press the lock-off button to lock position.
2. Press the power button to power down the pressure
washer.
3. Close the water tap or remove the siphon hose from
the water bucket.
4. Press the lock-off button of the gun to the unlock
position and squeeze the trigger to empty the water
from the hoses.
NOTICE: The gun, hoses, wands, nozzles, or foam cannon
should not be disconnected for as long as the water
remains in the hoses.
5. Disconnect and remove the gun, hoses, wands,
nozzles, or foam cannon.
6. Press the power button to power on the pressure
washer to empty the water in the pressure washer.
7. Press the power button again to power down the
pressure washer.
8. Remove the battery pack(s).
REMOTE CONTROL
The gun can be paired with the pressure washer to
function as a remote control.
Short Pressure Gun Pairing (Fig. K)
1. Insert the battery pack(s) and power on the pressure
washer.
2. Long-press the speed button on the pressure washer
unit until its three green lights start ashing.
NOTE: The ashing will last approximately 20 s, so the
gun can be paired only during this time. You could also
short-press the speed button on the washer to exit the
pairing mode any time.
3. Long-press the speed button on the gun until its
three green lights start ashing, which means the
pairing process has started.
NOTE: The ashing indicating the pairing process will
last approximately 10 s. You could short-press the speed
button on the gun to exit the pairing process any time.
4. The speed indicators on the washer and the gun will
display three green lights together for 3 s to indicate
the pairing was successful, then display two green
lights.
battery packs.
1. Raise the battery compartment cover by lifting the
front of the cover.
2. To attach, align the battery ribs with the mounting
slots in one and press the battery pack down until
you hear a “click”. Attach the other battery (Fig. I1).
3. To detach, depress the battery-release button and
pull the battery pack out (Fig. I2).
4. Close the battery compartment cover.
STARTING/STOPPING THE PRESSURE WASHER
(Fig. J)
To Start the Pressure Washer
NOTICE:
Do not start the pressure washer without water
supply connected and turned on. This may damage the
high-pressure seals and decrease pump life.
1. Ensure that the siphon hose, high-pressure hose,
gun, nozzle are connected properly.
2. Connect lance, wand, foam cannon, lter according
to your needs.
3. Choose one of below water supply ways:
◾ When using a garden hose (not provided), connect
the pressure washer to the garden hose and then
open the water tap.
◾ When using a water bucket, connect the lter to
the siphon hose and then immerse the lter and
the quick-coupler joint fully into the water bucket.
4. Install the battery pack(s).
5. Press the power button to power on the pressure
washer. The washer will always run at high speed
after each start.
NOTE: When the pressure washer is powered on but with
no further actions, the washer will turn off automatically
after 5 minutes of standby. During the rst several
minutes of standby, the speed indicator on the pressure
washer will ash three green lights, which indicates there
is no water owing into the siphon hose.
6. Hold the gun with both hands, press the unlock side
of the lock-off button and then squeeze the trigger
until a steady water ow is produced.
NOTE: If the lance is connected, hold the gun with one
hand and the lance with the other hand.
7. Start spray washing.
NOTE: It may take some time for the water to travel from
the source and come out of the nozzle as a steady spray.
To achieve a steady water ow quickly, you may want to:
To Next Page
Loading...
