EasyManua.ls Logo

EINHELL BT-GW 190 D - User Manual

EINHELL BT-GW 190 D
112 pages
Go to English
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Art.-Nr.: 15.749.90 I.-Nr.: 11032
BT-GW 190 D
k
Originalbetriebsanleitung
Schutzgas-Schweißgerät
t
Original operating instructions
Shielding Gas Welder
p
Mode d’emploi d’origine
Appareil à souder au gaz inerte
C
Istruzioni per l’uso originali
Saldatrice a gas inerte
lL
Original betjeningsvejledning
Beskyttelsesgas-svejseapparat
U
Original-bruksanvisning
MIG/MAG-svets
Bf
Originalne upute za uporabu
Uređaj za zavarivanje sa zaštitnim plinom
4
Originalna uputstva za upotrebu
Uređaj za varenje sa zaštitnim gasom
j
Originální návod k obsluze
Svářečka pro svařování v ochranné atmosféře
W
Originálny návod na obsluhu
Zváračka v ochrannej atmosfére
Vor Inbetriebnahme Bedienungsanleitung und Sicherheitshinweise
lesen und beachten
Read and follow the operating instructions and safety information before
using for the first time.
Avant la mise en service, lisez le mode dʼemploi et les consignes de
sécurité et respectez-les.
Prima della messa in esercizio leggete e osservate le istruzioni per lʼuso
e le avvertenze di sicurezza.
 Betjeningsvejledningen og sikkerhedsanvisningerne skal læses, inden
maskinen tages i brug. Alle anvisninger skal følges.
Läs igenom och beakta bruksanvisningen och säkerhetsanvisningarna
före användning.
Bf Prije puštanja u rad pročitajte i pridržavajte se ovih uputa za uporabu i
sigurnosnih napomena.
4 Prije puštanja u pogon pročitajte i uvažite uputstva za upotrebu i
napomene bezbednosti.
j Před uvedením do provozu si přečíst návod k obsluze a bezpečnostní
předpisy a oboje dodržovat.
W Pred uvedením do prevádzky si prečítajte a dodržiavajte návod na
obsluhu a bezpečnostné pokyny.
Anleitung_BT_GW_190_D_SPK1__ 24.01.13 15:06 Seite 1

Questions and Answers

  • B
    Brian FletcherAug 11, 2025
    What to do if the feed roller turns but doesn't feed any wire on my EINHELL Welding System?
    • B
      Brittany GallowayAug 11, 2025
      If the feed roller on your EINHELL Welding System turns but doesn't feed any wire, there could be several reasons: * The roller pressure might be incorrect: check the setting. * The roller brake could be set too firmly: check the setting. * The feed roller might be dirty or damaged: clean or replace it. * The hose package may be damaged: check the wire guide jacket. * The contact tube might be the wrong size, dirty, or worn: clean or replace it. * The welding wire might be welded to the gas nozzle or contact tube: release it.
  • J
    Jerry TurnerAug 17, 2025
    Why is the weld so poor with my EINHELL Welding System?
    • C
      Christopher MccormickAug 17, 2025
      If you're getting very poor welds with your EINHELL Welding System, first, verify that your current and wire feed settings are correct. Also, make sure you have enough gas flowing and that the pressure in your gas bottle is adequate.
  • G
    Gina HarrisAug 26, 2025
    What to do if my EINHELL Welding System stops working and the thermostat light is on?
    • M
      Melanie ShermanAug 26, 2025
      If your EINHELL Welding System stops working after extended use and the thermostat control light is on, it likely overheated because it was used for too long without allowing sufficient cooling time. Let the unit cool down for at least 20 to 30 minutes before resuming use.
  • J
    Jose RogersSep 1, 2025
    How to fix a feed roller that won't turn on my EINHELL Welding System?
    • L
      Laura ParsonsSep 1, 2025
      If the feed roller on your EINHELL Welding System isn't turning, make sure the power supply is properly connected. Also, check that the wire feed controller isn't set to 0.

Summary

1. Safety Regulations

Important Information About the Power Connection

Crucial details on connecting the equipment to the power supply, including voltage and interference.

General Safety Information

Provides essential safety guidelines and user responsibilities for operating the equipment.

4. Technical Data

5. Before Starting the Equipment

6. Operation

6.1 Setting

Explains how to adjust welding parameters like current, wire feed speed, and gas flow rate.

6.3 Welding

Step-by-step guide on performing the welding process, including workpiece preparation.

7. Cleaning, Maintenance and Ordering of Spare Parts

9. Troubleshooting

Special Connection Conditions (EN 61000-3-11)

Guarantee Certificate

EINHELL BT-GW 190 D Specifications

General IconGeneral
BrandEINHELL
ModelBT-GW 190 D
CategoryWelding System
LanguageEnglish

Related product manuals