EN
- 13 -
open the water supply.
•
The hose is now ready for use and you can
start with your work. Infinite adjustment of the
water jet from no water to fine spray and to
strong jet is possible by turning the front part
of the spray nozzle.
6.2 Winding up
•
When you are finished with your work,
close the spray nozzle first and then the
water supply. Before you wind up the hose,
open the spray nozzle again to release the
remaining water pressure and take the strain
off the hose.
•
Go back to the hose reel with the end of the
hose in hand, press the On/Off switch (Fig. 1 /
Item 3) in order to start the wind-up operation.
Allow the hose to be fully wound up or stop
the hose reel at any position for the length of
hose you want.
•
Protection function: The cordless hose reel
will switch off automatically if it experiences
any resistance. To restart, switch on the hose
reel again by pressing the On/Off switch (3).
•
If the hose becomes blocked, pull the hose
completely out of the hose reel and have it
wind up again. Take care to keep the twisting
of the hose to a minimum.
6.3 Charging the Lithium-Ion battery (not
included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.4 Battery capacity indicator (Fig. 7 / item
22)
Press the battery capacity indicator switch (23).
The battery capacity indicator (22) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depthdischarged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
7. Cleaning and maintenance
HAZARD!
Always take the battery out of the equipment
before starting any cleaning work.
The equipment is largely maintenance-free.
However, we recommend regular checks and
product care in order to ensure a long service life.
The inside of the hose reel housing is not allowed
to be cleaned with fl owing water, especially not at
high pressure.
7.1 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.2 Changing the water hose
If the hose reel is already fi tted with a hose, fi rst
pull out the hose to the mark.
Fig. 8: Remove the two screws from the
maintenance fl ap (9) and then fl ip the
maintenance fl ap from the top to the front.
Important! Risk of pinching - The hose reel
is allowed to be operated only when the
maintenance fl ap is fi tted.
Fig. 9: Another cover (Item 18) should now be
visible in the hose reel. If this is not the case,
carefully turn the hose reel to the rear. Remove
the cover by undoing the screw.
Fig. 10: Remove the fastening clasp (Item 19)
from the quick-lock coupling and then separate
the quick-lock coupling from the hose reel. To be
able to pull the hose out of the hose reel you must
also take the quick-lock coupling off the hose.
Fig. 11: To fi t a new hose, proceed in reverse
order. First pass the hose without quick-lock
coupling through the opening in the hose reel and
into the hose guide. Then feed the hose to the
rear around the hose reel.
Anl_GE_HR_18_30_Li_NA_SPK7.indb 13Anl_GE_HR_18_30_Li_NA_SPK7.indb 13 28.11.2023 09:00:0828.11.2023 09:00:08
To Next Page
Loading...
