Why EINHELL GC-MM 52 I AS equipment starts but does not develop its full power?
If your EINHELL Tools equipment starts but doesn't develop full power, the choke lever setting might be incorrect; set the choke lever to the correct position. Additionally, a soiled air filter can cause this issue, so clean the air filter. If the problem persists, the carburetor setting may be incorrect.
What to do if my EINHELL GC-MM 52 I AS Tools equipment does not start?
If your EINHELL Tools equipment isn't starting, make sure you're following the correct starting procedure. Also, check the spark plug; it might be sooted or damp. If it is, clean the spark plug or replace it with a new one. If these steps don't resolve the issue, the carburetor setting may be incorrect.
Why is my EINHELL GC-MM 52 I AS Tools chainsaw juddering, vibrating or not sawing properly?
If your EINHELL Tools chainsaw is juddering, vibrating, or not sawing properly, the chain tension might be too loose, so you should adjust it. Also, the chain might be blunt or worn, so re-sharpen or replace the chain. Ensure that the saw teeth are pointing in the correct direction; if not, reinstall the saw chain with the teeth facing in the correct direction.
What to do if the chain/guide rail of my EINHELL GC-MM 52 I AS is hot?
If the chain or guide rail of your EINHELL Tools is hot, start by checking if there's oil in the tank and fill it up if needed. Also, the oil tank cap breather might be blocked, so clean it. The oil outlet could also be blocked, so clear it. Furthermore, the chain might be blunt, so re-sharpen or replace it. Lastly, check the chain tension, as it might be overtensioned.
Why does my EINHELL Tools engine smokes excessively?
If your EINHELL Tools engine is smoking excessively, the fuel mix might be incorrect. Use the correct fuel mix (see fuel mixing table). If the problem persists, the carburetor setting may be incorrect.
Why is the saw chain of my EINHELL Tools dry?
If the saw chain is dry, it might be because there's no oil in the tank, so fill it up with oil. Another reason could be a blocked oil tank cap breather, so clean the oil tank cap. Also, the oil outlet might be blocked, so clear the oil outlet.
What to do if the engine of my EINHELL Tools does not run smoothly?
If your EINHELL Tools engine isn't running smoothly, the electrode gap on the spark plug might be incorrect. Clean the spark plug and adjust the electrode gap, or fit a new spark plug. If the problem persists, the carburetor setting may be incorrect.
Fitting the appropriate guard hood to prevent objects being thrown out by the equipment.
Read operating instructions carefully and familiarize yourself with the equipment's use and settings.
Check ground, wear footwear, refuel safely, replace defective silencers, inspect scythe before use.
Wear protective clothing, store safely, switch off before putting down, hold firmly with both hands.
Take warnings for blade operation, avoid recoil, check blade for damage, do not use if damaged.
Keep body away from chain, do not use up a tree, expect recoil, carry safely, follow lubrication instructions, keep handles dry.
Kickback occurs if tip touches object or chain jams. Can cause injuries. Take precautions.
Keep body away from blades, never remove cuttings with blade running, carry by handle, fit cover.
Information on recommended fuels, oil mixing ratios, and storage of fuel.
Step-by-step guide for starting a cold engine, including primer and choke settings.
Instructions for extending cutting line, cutting methods, trimming, and around obstacles.
Preparations including chainsaw condition, oil level, chain tension and sharpening.
Instructions for adjusting blade angle, cutting dense growth, and hedge sides.
Covers techniques for cutting wood, sawing branches, and kickback prevention.
Procedures for maintaining the air filter, spark plug, carburetor settings, and idling speed.
Table of common faults, possible causes, and remedies for equipment problems.
General| Type | String trimmer |
|---|---|
| Head type | - |
| Handle type | U-type handle |
| Cutting width | 420 mm |
| Line diameter | 2.4 mm |
| Product color | Black, Grey, Red |
| Rotational speed | 9600 RPM |
| Fuel tank capacity | 0.9 L |
| Vibration emission | 21.3 m/s² |
| Brand compatibility | Einhell |
| Engine displacement | 51.7 cm³ |
| Line length supplied | 4 m |
| Cutting diameter (max) | - mm |
| Power source | Gasoline |
Weight and Dimensions| Depth | 310 mm |
|---|---|
| Width | 320 mm |
| Length | 1020 mm |
| Weight | 8000 g |
| Package weight | 16500 g |
To Next Page