EINHELL TC-SS 405 E User Manual

GB
- 9 -
Load factor:
A load factor of 10 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (120W)
for no longer than the time stipulated on the spe-
cifi cations label (10 min). If you fail to observe
this time limit the motor will overheat. During the
OFF period the motor will cool again to its starting
temperature.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L
pA
sound pressure level ..................... 90,1 dB(A)
K
pA
uncertainty ............................................. 3 dB
L
WA
sound power level ..................... 103,1 dB(A)
K
WA
uncertainty ............................................. 3 dB
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
5. Before starting the equipment
5.1 General information
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched
on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been
processed before, watch out for foreign bo-
dies such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine’s moving parts run smoothly.
•
Before you connect the machine to the power
supply, make sure the data on the rating plate
is the same as that for your mains.
5.2 Assembly
Caution! Pull out the power plug before carrying
out any maintenance and conversion work on
your fretsaw.
For greater stability, fasten the equipment in
addition to a workbench or similar (Fig. 8). Suita-
ble fastening materials such as screws etc. are
available from your dealer.
5.2.1 Mounting the saw blade guard and the
sawdust blower facility (Fig. 4/5)
•
Fasten the retaining pin and the saw blade
guard to the arm (19) as shown in Fig. 4.
•
The saw blade guard can be fixed at various
heights with the clamping screw (11).
•
Mount the blow-off device (16) as shown in
Fig. 6.
5.2.2 Changing the blade (Fig. 1/3/6a)
•
Turn the clamp lever (14) counterclockwise to
release the saw blade (15).
•
Unscrew the left cover (4).
•
First take the blade out of the top blade hol-
der (13), pressing down the upper pendulum
arm as you do so.
•
Then take the blade out of the bottom blade
holder (8).
•
Pull the blade up and out through the table
insert (18).
•
Install the new blade in reverse order.
•
Use the supplied Hexagon key (24) to clamp-
fit the saw blade in the holder
Caution: Always insert the blade so that the
teeth point toward the saw table.
Anl_TC_SS_405_E_GB_Korea.indb 9Anl_TC_SS_405_E_GB_Korea.indb 9 20.07.2022 14:06:3020.07.2022 14:06:30

EINHELL TC-SS 405 E Specifications

General

Maximum power	120 W
AC input voltage	230 V
AC input frequency	50 Hz
Blade length	127 mm
Throat depth	406 mm
Product color	Black, Grey, Red
Stroke height	14 mm
Idle speed (max)	1600 RPM
Idle speed (min)	400 RPM
Cutting height @ 45°	20 mm
Cutting height @ 90°	52 mm

Weight and Dimensions

Weight	12500 g
Table depth	250 mm
Table width	408 mm
Package depth	644 mm
Package width	316 mm
Package height	330 mm
Package weight	13450 g