ELBE 207-SM User Manual

1
207-SM Control Panel Instruction 12VDC and 24VDC For Swing Gates
General safety rules
WARNING: Unskilled personnel should never be allowed to assemble, repair or adjust the devices and all necessary
precautions must be taken to prevent accidents: power supply disconnected (including backup batteries if present).This
product is not suitable for installation in explosive atmospheres.
Keep this handbook carefully, store it attached to the technical installation leaflet in a safe place where it is
available to anyone who may need it and make sure that all involved personnel are aware of this.
Type of product
The 207 control panel has been designed to control 1 or 2 operators 12VDC and a 24VDC version for swing gates. It has an
on-board integrated radio receiver. It is also possible to set the slowing down and anti-crushing features that grant an easy
and safe installation, free from interference and protected against atmospheric and electrostatic discharges. The control
board 207 has succeeded all tests concerning the electromagnetic emissions and the immunity to the interference as
provided by the European rules in force. It conforms to the directives EMC 89/336/CEE, 92/31/CEE, BT 73/23/CEE and
93/68/CEE

ELBE 207-SM Specifications

General

Brand	ELBE
Model	207-SM
Category	Control Panel
Language	English

Summary

General Safety and Product Information

General safety rules

Essential safety instructions for operating, repairing, or adjusting the control panel.

Product type overview

Details the function and application of the 207 control panel for swing gates.

System Features and Safety

Obstacle detection system

Explains how the system detects obstacles and adjusts gate movement accordingly.

Battery charging

Describes the control board's ability to recharge a connected battery.

General safety advice

Reinforces precautions for safe installation and operation, emphasizing qualified personnel.

Terminal and Wiring Overview

Terminal layout diagram

Visual representation of the control panel's terminal connections and component layout.

Terminal and LED Descriptions

Input/output terminal functions

Details the purpose and connection for each terminal on the control panel.

Control panel LED indicators

Explains the meaning and status of various LEDs on the circuit board.

Configuration Options

Trimmer functions

Description of AMP, RALL, and VELOC trimmers for adjusting gate operation.

SW1 dip switch settings

Configuration options for SW1 dip switch on the control panel.

SW2 dip switch settings

Configuration options for SW2 dip switch on the control panel.

Fuses, Remote Control, and Checks

Fuse description

Details the location, type, and rating of fuses on the control panel.

Remote control operations

Instructions for storing and cancelling remote control codes.

Preliminary checks

Essential checks to perform before setting up the control panel.

Wiring the 207 Controller (Steps 1 & 2)

Cable information and AC transformer

Specifies cable requirements and connection to the AC transformer.

Motor wiring and SW1-1 setting

Illustrates motor connections and SW1-1 dip switch configuration.

Photocells

Photocell installation and function

Explains how photocells are installed and their role in gate operation.

Surface mounted photocell placement

Guidance on the proper placement of surface-mounted photocells.

Adding Photocells (Wiring Step 3)

Photocell wiring diagrams

Diagrams showing how to wire one or two pairs of photocells.

Photocell configuration notes

Important notes on jumpers and alignment for photocell installation.

Programming the 207C Circuit Board

Remote control programming steps

Step-by-step guide for programming remote controls to the panel.

Verifying motor direction

Procedure to check and correct motor rotation direction.

Generating random fob codes

Instructions for generating random codes for specific remote models.

Automatic Programming Procedure

Automatic programming steps

Detailed steps for the automatic programming of gate working times and speeds.

Standards compliance and trimmer fine-tuning

Notes on safety standards and adjusting trimmers after programming.

Manual Programming of Times and Speeds

Manual programming steps overview

Introduction and initial steps for manual gate programming.

Motor direction verification

Procedure to verify and correct motor direction for manual programming.

Programming first door opening

Steps for programming the opening sequence of the first motor.

Manual Programming of Times and Speeds (Cont.)

Programming second door opening and delay

Steps for programming the second motor's opening sequence and delay.

Programming door closing sequences

Steps for programming the closing sequence of both motors.

Standards compliance and trimmer fine-tuning

Notes on safety standards and fine-tuning speeds after programming.

Automation Closing and Radio Code Programming

Setting automatic closing timers

Procedure to enable and set the automatic closing pause time.

Deleting automatic closing settings

How to reset or delete automatic closing time settings.

Programming and deleting radio codes

Instructions for adding or removing radio codes for START/PEDESTRIAN.

Additional Equipment Programming

LEB Radio-keypad programming steps

Step-by-step guide for programming the LEB Radio-keypad.

Wireless Radio-Keypad Operations

Installation and positioning

Guidance on installing and positioning the wireless radio-keypad.

Changing keypad combinations

Instructions for changing the keypad's access combination.

Keypad factory reset

Procedure for performing a factory reset on the keypad.