Electrolux 6 GN 1/1 User Manual (English)

Other manuals for Electrolux 6 GN 1/1

Questions and Answers:

J
Joe HermanSep 10, 2025
What causes the boiler safety thermostat to trip in Electrolux 6 GN 1/1 Oven?
- C
  Carolyn PowellSep 10, 2025
  If the boiler safety thermostat trips and there is an overtemperature in the boiler of your Electrolux Oven, it could be due to missing water, limestone accumulation, incorrect insertion of the TC probe sensor, damage to the safety thermostat bulb or capillary, heat leakage in the safety thermostat body area, a BOT parameter set too high, or a room temperature below 5°C. The oven will not be able to produce steam with the boiler; an alternative device will be used, but performance will be reduced. Call service to restore boiler functionality.
C
Carl NielsenAug 25, 2025
Why does my Electrolux 6 GN 1/1 show a boiler overtemperature warning?
- A
  alyssapittsAug 25, 2025
  If your Electrolux Oven displays a boiler overtemperature warning, it could be due to missing water in the boiler (for electric heated appliances), limestone accumulation, or an incorrectly set parameter. Wait for the boiler temperature to cool down until the alarm disappears. Run a cleaning program that includes a rinse and descale cycle, using the correct amount of descaling tablets as indicated in the manual. If the alarm reappears, repeat the descaling process. If the problem continues, contact Service.
M
Megan CoxAug 25, 2025
What causes a cavity overtemperature in my Electrolux 6 GN 1/1?
- J
  Joan DouglasAug 26, 2025
  If your Electrolux Oven shows a cavity overtemperature error, it could be because the cavity is dirty or the parameter COT is set too low. Launch a cooling cycle; if that's not possible, open the door and let the oven cool down, then clean the cavity. Once the temperature drops, you can start a new cooking cycle. If the error appears again, contact Service.
C
charles24Aug 26, 2025
Why is my Electrolux 6 GN 1/1 Oven showing a component compartment temperature warning?
- M
  Matthew PhillipsAug 26, 2025
  If your Electrolux Oven is displaying a component compartment temperature warning, this may be due to a dirty filter or a room temperature that is too high. Check the room temperature, ensuring the oven has fresh air to cool the electronic compartment. Clean the filter and allow the oven to cool before cooking. If the problem continues, contact Service.
C
Cassandra BaxterSep 12, 2025
What does lower inverter communication problem mean in Electrolux 6 GN 1/1 Oven?
- T
  tapiadebraSep 12, 2025
  If your Electrolux Oven is showing a lower inverter communication problem, it could be due to an issue with the motor inverter or a connection/electrical issue. Try switching the oven OFF and then ON again. If the problem persists, call Service.
C
Cynthia DavisSep 13, 2025
What does upper inverter communication problem mean in Electrolux Oven?
- E
  Emily ColeSep 13, 2025
  If your Electrolux Oven is showing an upper inverter communication problem, it could be due to an issue with the motor inverter or a connection/electrical issue. Try switching the oven OFF and then ON again. If the problem persists, call Service.
C
Christopher CollinsSep 4, 2025
What does it mean if my Electrolux Oven detected a problem with the oxygen sensor?
- C
  Courtney TorresSep 4, 2025
  If your Electrolux Oven detects a problem with the oxygen sensor, it is likely due to a lambda probe failure. You can continue using the oven in Steam under 100°, but cooking results in Steam mode may be different from usual. If cooking results are persistently unsatisfactory, call Service.
L
Lisa NelsonSep 5, 2025
What to do if Electrolux 6 GN 1/1 shows water drain NTC failure?
- J
  Jacqueline LawrenceSep 5, 2025
  If your Electrolux Oven shows a water drain NTC failure, it could be due to a connector failure, NTC sensor failure, or PCB failure. The oven can continue to work. Call Service to fix the issue.
D
Daniel LoganAug 31, 2025
What does Cavity SSR NTC high temperature (NTC3) mean in Electrolux 6 GN 1/1?
- H
  henryjosephAug 31, 2025
  If your Electrolux Oven displays a Cavity SSR NTC high temperature (NTC3) warning, it could be due to a dirty inlet air filter, cooling fan failure, the cooling inlet sucking in warm/hot air, the oven being installed near a hot machine, or steam/heat leakage in the electronic compartment. Do not switch the oven off; wait for the temperature to decrease. Clean the inlet air filter. Check with a thin strip of paper whether a consistent air flow can be detected at the cooling air inlet; if not, call Service. Check if the inlet cooling air may be affected by heat produced in the kitchen; if so, stop working with those appliances and inform Service. If the error persists, call Service.
T
Tracy CurtisAug 30, 2025
Why does my Electrolux Oven stop cycles needing the boiler?
- L
  lopezscottAug 30, 2025
  If your Electrolux Oven stops a cycle that requires the boiler, it could be due to the water supply (pressure/quality of water) or an electrical insulation problem with the water level sensors. Check if the water supply is open and if the water pressure is not too low. Verify if the water filter is clogged; clean or replace it. If the problem persists, it might indicate a mechanical problem with the boiler operation, in which case you should call Service.

Electrolux 6 GN 1/1 Specifications

General

Net Weight	70 kg
Weight	70 kg
Material	Stainless steel
Type of oven	Convection
External dimensions, Height	710 mm
External dimensions, Width	890 mm
External dimensions, Depth	700 mm
Power Consumption	6.5 kW
Temperature Range	50 - 300 °C
Dimensions (WxDxH)	890x700x710 mm