EasyManua.ls Logo

Electrolux 6 GN 1/1 - User Manual

Electrolux 6 GN 1/1
38 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Electrical and Gas Oven
Combi DIGITAL
EN
User manual *
*Original instructions
0595403Z01- 2020.01

Table of Contents

Other manuals for Electrolux 6 GN 1/1

Preview: Installation And Operating Manual
Installation And Operating Manual34 pages

Questions and Answers

  • J
    Joe HermanSep 10, 2025
    What causes the boiler safety thermostat to trip in Electrolux 6 GN 1/1 Oven?
    • C
      Carolyn PowellSep 10, 2025
      If the boiler safety thermostat trips and there is an overtemperature in the boiler of your Electrolux Oven, it could be due to missing water, limestone accumulation, incorrect insertion of the TC probe sensor, damage to the safety thermostat bulb or capillary, heat leakage in the safety thermostat body area, a BOT parameter set too high, or a room temperature below 5°C. The oven will not be able to produce steam with the boiler; an alternative device will be used, but performance will be reduced. Call service to restore boiler functionality.
  • C
    Carl NielsenAug 25, 2025
    Why does my Electrolux 6 GN 1/1 show a boiler overtemperature warning?
    • A
      alyssapittsAug 25, 2025
      If your Electrolux Oven displays a boiler overtemperature warning, it could be due to missing water in the boiler (for electric heated appliances), limestone accumulation, or an incorrectly set parameter. Wait for the boiler temperature to cool down until the alarm disappears. Run a cleaning program that includes a rinse and descale cycle, using the correct amount of descaling tablets as indicated in the manual. If the alarm reappears, repeat the descaling process. If the problem continues, contact Service.
  • M
    Megan CoxAug 25, 2025
    What causes a cavity overtemperature in my Electrolux 6 GN 1/1?
    • J
      Joan DouglasAug 26, 2025
      If your Electrolux Oven shows a cavity overtemperature error, it could be because the cavity is dirty or the parameter COT is set too low. Launch a cooling cycle; if that's not possible, open the door and let the oven cool down, then clean the cavity. Once the temperature drops, you can start a new cooking cycle. If the error appears again, contact Service.
  • Q
    qhillSep 23, 2025
    What causes cavity lower gas burner blower speed issue in Electrolux 6 GN 1/1 Oven?
    • B
      Brendan TapiaSep 23, 2025
      If your Electrolux Oven has a cavity lower gas burner blower speed issue, it could be due to a burner blower motor overload caused by dirt or oxidation, or another electrical/mechanical issue. The burner fan does not reach the desired speed. Call Service.
  • C
    Cassandra BaxterSep 12, 2025
    What does lower inverter communication problem mean in Electrolux 6 GN 1/1 Oven?
    • T
      tapiadebraSep 12, 2025
      If your Electrolux Oven is showing a lower inverter communication problem, it could be due to an issue with the motor inverter or a connection/electrical issue. Try switching the oven OFF and then ON again. If the problem persists, call Service.
  • R
    Rebecca JenkinsSep 15, 2025
    What to do if there are issues with valves/pumps activations in Electrolux Oven?
    • S
      Steven PenningtonSep 16, 2025
      If your Electrolux Oven shows an error related to valves/pumps activations, caused by diagnostics according to the error number displayed, switch the oven OFF and then ON again. If the error persists, follow the instructions displayed. If the error persists, manually clean the oven cavity and call Service.
  • C
    Christopher CollinsSep 4, 2025
    What does it mean if my Electrolux Oven detected a problem with the oxygen sensor?
    • C
      Courtney TorresSep 4, 2025
      If your Electrolux Oven detects a problem with the oxygen sensor, it is likely due to a lambda probe failure. You can continue using the oven in Steam under 100°, but cooking results in Steam mode may be different from usual. If cooking results are persistently unsatisfactory, call Service.
  • L
    Lisa NelsonSep 5, 2025
    What to do if Electrolux 6 GN 1/1 shows water drain NTC failure?
    • J
      Jacqueline LawrenceSep 5, 2025
      If your Electrolux Oven shows a water drain NTC failure, it could be due to a connector failure, NTC sensor failure, or PCB failure. The oven can continue to work. Call Service to fix the issue.
  • J
    Jennifer RobinsonSep 23, 2025
    What causes cavity upper gas burner blower speed issue in Electrolux 6 GN 1/1?
    • J
      Jeff PachecoSep 23, 2025
      If your Electrolux Oven has a cavity upper gas burner blower speed issue, it could be due to a burner blower motor overload caused by dirt or oxidation, or another electrical/mechanical issue. The burner fan does not reach the desired speed. Ovens with a boiler can cook in 100° steam mode. To restore full oven functionality, call Service.
  • T
    Tracy CurtisAug 30, 2025
    Why does my Electrolux Oven stop cycles needing the boiler?
    • L
      lopezscottAug 30, 2025
      If your Electrolux Oven stops a cycle that requires the boiler, it could be due to the water supply (pressure/quality of water) or an electrical insulation problem with the water level sensors. Check if the water supply is open and if the water pressure is not too low. Verify if the water filter is clogged; clean or replace it. If the problem persists, it might indicate a mechanical problem with the boiler operation, in which case you should call Service.

Summary

WARNING AND SAFETY INFORMATION

General information

Provides essential information for safe machine use and manual understanding.

Personal protection equipment

Details the necessary Personal Protection Equipment (PPE) for various stages of machine use.

General safety

Highlights the importance of electric and mechanical safety devices for protection.

General safety rules

Outlines rules for safe operation, including guards and maintenance.

Safety signs to be placed near the machine area

Explains the meaning of prohibition and danger signs used on the machine.

Reasonably foreseeable improper use

Identifies uses and activities considered improper and potentially risky.

Machine cleaning and maintenance

Provides instructions for maintaining oven performance and safety through cleaning.

WARRANTY

Warranty terms and exclusions

Details the conditions and limitations of the product warranty coverage.

GENERAL INFORMATION

Intended use and restrictions

Specifies the appliance's intended purpose and any restrictions on its use.

NORMAL MACHINE USE

Characteristics of personnel trained for normal machine use

Ensures personnel are trained and skilled for safe machine operation.

Characteristics of personnel enabled to operate on the machine

Responsibilities for ensuring personnel understand manual and receive training.

Operator qualified for normal machine use

Specifies the required knowledge and experience for qualified operators.

PRODUCT DESCRIPTION

Control panel

Identifies the components of the digital control panel and their functions.

OPERATING

QUICK GUIDE STEPS

Concise steps for operating the oven from start-up to shutdown.

Switch the oven ON

Procedure for turning the oven on and off using the power button.

Displays and controls description

Cleaning cycle

OVEN CARE

Care information

Appliance cleaning

Information on cleaning the oven, including cooking chamber and boiler.

Boiler descaling (dESC)

Repair and extraordinary maintenance

Guidelines for repair and maintenance performed by authorized personnel.

Maintenance intervals

Decommissioning

TROUBLESHOOTING

Anomaly table

A comprehensive table listing anomalies, causes, and actions.

MACHINE DISPOSAL

Electrolux 6 GN 1/1 Specifications

General IconGeneral
Net Weight70 kg
Weight70 kg
MaterialStainless steel
Type of ovenConvection
External dimensions, Height710 mm
External dimensions, Width890 mm
External dimensions, Depth700 mm
Power Consumption6.5 kW
Temperature Range50 - 300 °C
Dimensions (WxDxH)890x700x710 mm

Related product manuals