Why does Electrolux Oven show boiler excessive temperature raising time?
If your Electrolux Oven is showing a warning about excessive boiler temperature raising time, the oven has detected a low performance in the boiler. It is still possible to cook, so verify the cooking results. If the warning persists, call Service.
Why does my Electrolux Oven stop cycles needing the boiler?
If your Electrolux Oven stops a cycle that requires the boiler, it could be due to the water supply (pressure/quality of water) or an electrical insulation problem with the water level sensors. Check if the water supply is open and if the water pressure is not too low. Verify if the water filter is clogged; clean or replace it. If the problem persists, it might indicate a mechanical problem with the boiler operation, in which case you should call Service.
What causes high temperature on water drain in Electrolux 6 GN 1/1 Oven?
If you notice a high temperature on the water drain of your Electrolux Oven, it might be due to a lack of water in the drain system. Check that the oven has a water supply and pour some water on the bottom cavity filter. If the problem continues, call Service.
Why is water measured inconsistent with valves state in Electrolux 6 GN 1/1 Oven?
If the water measurement is inconsistent with the valve state in your Electrolux Oven, it could be due to a water supply valve being closed or partly closed, a temporary lack of water supply pressure, a flow meter failure, or a water system issue. The oven can still work, but you should check the cooking results. Check if the water supply valve is open and ensure the water pressure is above 1.5 bar. If the problem persists, contact Service.
How to resolve Boiler SSR NTC high temperature in Electrolux 6 GN 1/1 Oven?
If your Electrolux Oven is showing a Boiler SSR NTC high temperature warning, it might be due to a dirty inlet air filter, cooling fan failure, the cooling inlet sucking in warm or hot air, the oven being installed near a hot machine, or steam/heat leakage in the electronic compartment. Do not switch the oven off; wait for the temperature to decrease. Clean the inlet air filter. Check for consistent airflow at the cooling air inlet with a thin strip of paper; if not, call Service. Also, check if the inlet cooling air is affected by heat produced in the kitchen; if so, stop working with those appliances and inform Service. If the error persists, call Service.
What to do if water boiler level is not reached in Electrolux Oven?
If the water boiler level is not reached in time in your Electrolux Oven, it could be due to a water supply valve being closed or partly closed, a temporary lack of water supply pressure, a boiler water level sensor failure, or boiler leakage. Ensure the water supply valve is fully open and the water filter has no obstructions; clean it if needed. The oven can continue to work in Convection mode. Unless the water is missing from the mains, the oven can continue to work in recovery mode.
How to fix a cooling fan issue in Electrolux 6 GN 1/1 Oven?
If you're experiencing a cooling fan issue with your Electrolux Oven, it could be due to a dirty inlet air filter or a cooling fan failure. Clean the inlet air filter. Check for consistent airflow at the cooling air inlet using a thin strip of paper. If you don't detect airflow, call Service.
Why is my Electrolux 6 GN 1/1 Oven showing a component compartment temperature warning?
If your Electrolux Oven is displaying a component compartment temperature warning, this may be due to a dirty filter or a room temperature that is too high. Check the room temperature, ensuring the oven has fresh air to cool the electronic compartment. Clean the filter and allow the oven to cool before cooking. If the problem continues, contact Service.
What causes a cavity overtemperature in my Electrolux 6 GN 1/1?
If your Electrolux Oven shows a cavity overtemperature error, it could be because the cavity is dirty or the parameter COT is set too low. Launch a cooling cycle; if that's not possible, open the door and let the oven cool down, then clean the cavity. Once the temperature drops, you can start a new cooking cycle. If the error appears again, contact Service.
Why does my Electrolux 6 GN 1/1 show a boiler overtemperature warning?
If your Electrolux Oven displays a boiler overtemperature warning, it could be due to missing water in the boiler (for electric heated appliances), limestone accumulation, or an incorrectly set parameter. Wait for the boiler temperature to cool down until the alarm disappears. Run a cleaning program that includes a rinse and descale cycle, using the correct amount of descaling tablets as indicated in the manual. If the alarm reappears, repeat the descaling process. If the problem continues, contact Service.
General| Net Weight | 70 kg |
|---|---|
| Weight | 70 kg |
| Material | Stainless steel |
| Type of oven | Convection |
| External dimensions, Height | 710 mm |
| External dimensions, Width | 890 mm |
| External dimensions, Depth | 700 mm |
| Power Consumption | 6.5 kW |
| Temperature Range | 50 - 300 °C |
| Dimensions (WxDxH) | 890x700x710 mm |
Provides essential information for safe machine use and manual understanding.
Details the necessary Personal Protection Equipment (PPE) for various stages of machine use.
Highlights the importance of electric and mechanical safety devices for protection.
Outlines rules for safe operation, including guards and maintenance.
Explains the meaning of prohibition and danger signs used on the machine.
Identifies uses and activities considered improper and potentially risky.
Provides instructions for maintaining oven performance and safety through cleaning.
Details the conditions and limitations of the product warranty coverage.
Specifies the appliance's intended purpose and any restrictions on its use.
Ensures personnel are trained and skilled for safe machine operation.
Responsibilities for ensuring personnel understand manual and receive training.
Specifies the required knowledge and experience for qualified operators.
Identifies the components of the digital control panel and their functions.
Concise steps for operating the oven from start-up to shutdown.
Procedure for turning the oven on and off using the power button.
Information on cleaning the oven, including cooking chamber and boiler.
Guidelines for repair and maintenance performed by authorized personnel.
A comprehensive table listing anomalies, causes, and actions.
To Next Page
