Need help?Do you have a question about the Eliet E401 and is the answer not in the manual?
General| Brand | Eliet |
|---|---|
| Model | E401 |
| Category | Lawn Mower |
| Language | English |
Read manual for safe and reliable use; failure to observe may cause injury or damage.
Note identification data for your machine in boxed areas.
Mail completed warranty card within one month of purchase to obtain warranty.
Symbol used to draw attention to specific info or where to find additional info.
Notice identifying safe usage habits to prevent incorrect actions and damage.
Notice warning about extreme danger and need to remain alert for safety.
Identification of parts by name for improved understanding of descriptions.
Stickers warning about hand injuries, general safety regulations, and engine shut-off for maintenance.
Describes safety features like operation handle, steel compartment, belt cover, lateral guard, and warnings.
Warning about accidents due to carelessness; read manual, contact dealer, check dealer duties, observe stickers.
Operate attentively, avoid danger, use only for dethatching, set blade depth carefully, owner not liable for improper settings.
Operator must be conversant, liable, mature; keep children/animals away.
PPE reduces risk; wear suitable clothing, gloves, footwear, goggles, hearing protection, dust mask.
Safe position behind machine; keep bystanders away (10m); stop blade drive if zone entered.
Regular maintenance essential for safety and machine life; follow maintenance schedule.
Set box on surface, check arrows, cut side, pull out flaps, remove machine.
Push handlebar back until it clicks, secure nuts on both sides.
Instructions for assembling collector unit parts, attaching bag, and mounting metal deflector.
Dealer explains workings, hazards, maintenance, bolt tightening, fuel/oil, test drive, lubrication.
Check oil level, fuel, air filter, blades, belt tension, depth setting, covers, safety provisions before operation.
Refuel when low; use fresh, unleaded petrol; observe flammability safety.
Work with good light; verify area conditions; remove foreign objects; cut grass short; avoid wet lawns.
Check oil/fuel levels; refer to engine manual; set controls; start engine.
Check oil/fuel levels; refer to engine manual; open fuel tap; set controls; start engine.
Operate attentively, avoid danger, use only for dethatching, set blade depth carefully.
Never run engine in closed environment; wear protective clothing; operator must be alert; work with sufficient visibility and light.
Procedure for dethatching; place on lawn, lift blades, engage, acquire speed, lower, push at medium speed.
Empty when full or losing moss; release bracket, halt blades, unhook unit, fold mudguard, clip back.
Switch throttle/knob to "OFF"; close fuel tap if equipped.
Switch throttle/knob to "OFF"; close fuel tap if equipped.
Clean machine after each use for visual check; check engine, cooling fins, fuel cap, bushings.
Clean machine after each use for visual check; check engine, cooling fins, fuel cap, bushings.
Remove raked moss; sow new grass, fertilise, aerate, sand, and irrigate for lawn renovation.
Follow procedures for safe transport: engine off, adults only, secure machine, use planks, avoid slopes.
Dealer help desk for support; use authorised dealer/service centre; submit model/serial numbers; use original parts.
Table outlining routine checks before operation and maintenance after 20 hours, with section references.
Lists recommended lubricants for engine, hinges, and wheel axles.
Checks to be performed before starting the machine for safe operation.
Check parts are not deformed, seams not cracked, no excess play; perform repairs if needed.
Check oil level using dipstick; wipe and re-insert to get accurate reading.
Locate air filter under cover; clean sponge/paper filters with petrol/compressed air.
Correct depth setting for maximum efficiency; carry out with engine off and blades stopped.
Check belt tension with engine off; tilt machine, remove cover, press belt parts to check tension.
Maintenance tasks to be performed after the initial 20 hours of machine operation.
Ensure engine is off and level; collect oil, empty, replace plug, refill with recommended oil, check level.
Check/change spark plugs for Honda engines; verify electrode gap is 0.8mm; check ignition quality.
Procedure same as cleaning air filter; new filters available from dealer.
Covers lubricating bearings and hinges to prevent wear and friction.
Adjust belt tension with engine off; tilt machine, remove cover, loosen nuts, tighten bolts.
Includes removal of blade axle, changing blades, placement, and finishing checks for safe operation.
Follow steps for extended storage: overhaul, fasten bolts, empty fuel, detach spark plug, treat rust, store in cool/dry area.
Details engine selection, handlebar, operating width, blade clutch, chassis, depth control, weight, and blades.
Declares machines designed and manufactured to comply with CE regulations; provides sound power levels and company details.
To Next Page
