12
Electric Shock Hazard: To prevent electrical shock, disconnect power before
servicing unit. Use only a properly grounded and polarized electric outlet.
CARE AND USE
ADJUSTING THE THERMOSTAT
PROPERTY DAMAGE
SEASONAL STORAGE/DRAINAGE
approx. 93°C
Scalding Hazard: Do not allow
water to boil. May result in
severe burns.
CLEANING THE FAUCET AND TANK
Only use mild cleaners to clean the
faucet and plastic components.
Cleaners with acids, abrasives,
alkaline or organic solvents will result in
deterioration of the plastic components and
void the warranty.
Regularly inspect the unit for any signs
of leakage. If there are signs of water
damage, immediately remove the unit
from service and contact an Authorized
InSinkErator Service Agent.
A drain pan, plumbed to an appropriate
drain or outfitted with a leak detector,
should be used in those applications
where any leakage could cause
property damage.
Anytime the steaming hot water tap is not used for
extended periods of time, unplug and drain unit. If
it is below freezing you will need to unplug the unit
and drain it.
Disconnect power from unit (unplug unit).
Push hot water tap button and allow
water to flow until it is cool.
Shut the cold water supply off at the valve.
Disconnect tubes from the tank.
Unhook tank from wall.
Hold tank upside down and drain the
water into the sink.
Towel dry any water drippings from
tank area.
Reinstall tank to wall and reconnect tubes.
Remove and discard filter cartridge,
if applicable.
To put back into working order, install
new filter cartridge (if applicable) and
turn on cold water supply at valve. Push
the hot water tap faucet button and
hold until water flows from the spout.
Reconnect the electrical cord.
Personal Injury:
Regularly check for signs of corrosion
by examining the appearance of the
dispensed water every three (3) months.
If there is any discoloration or rusty
appearance, unplug and drain unit
as described in the Seasonal
Storage/Drainage section on this
page of the manual.
If the water discoloration remains after
draining and refilling unit, discontinue
use and contact an authorized
InSinkErator service agent.
Factory temperature pre-set
is approximately 93˚C
(96˚C for HWTF-1,-2,-3.)
Adjust the thermostat
slowly, turning the dial
clockwise to increase
temperature or counter clockwise to
decrease
temperature, then activate faucet button
for 20 seconds to bring in fresh water
to be heated at the new setting. Allow
5-7 minutes for water to reach new
temperature.
To reset the thermostat to the factory pre-set, turn
the indicator two notches to the right of vertical.
HOT100 Faucet: 1-year warranty
Stainless Steel Tank: 1-year warranty
Filtration System (excluding replaceable filtration cartridge): 1-year warranty
This warranty is provided by InSinkErator, a business unit of Emerson Electric Co., (“InSinkErator” or “Manufacturer” or
“we” or “our” or “us”) to the original consumer owner of the InSinkErator product with which this warranty is provided (the
“InSinkErator Product”), and any subsequent owner of the residence in which the Product was originally installed (“Customer”
or “you” or “your”).
InSinkErator warrants to Customer that your InSinkErator Product will be free from defects in materials and workmanship, subject
to the exclusions described below, for the “Warranty Period”, commencing on the later of: (a) the date your InSinkErator Product
is originally installed, (b) the date of purchase, or (c) the date of manufacture as identified by your InSinkErator Product serial
number. You will be required to show written documentation supporting (a) or (b). If you are unable to provide documentation
supporting either (a) or (b), the Warranty Period commencement date will be determined
by Manufacturer, in its sole and absolute discretion, based upon your InSinkErator Product serial number.
What is Covered
This warranty covers defects in materials or workmanship, subject to the exclusions below, in InSinkErator Products used by a
consumer Customer for residential use only, and includes all replacement parts and labor costs. YOUR SOLE AND EXCLUSIVE
REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE INSINKERATOR
PRODUCT.
What is not Covered
This limited warranty does not extend to and expressly excludes:
• Losses or damages or the inability to operate your InSinkErator Product resulting from conditions beyond the
Manufacturer’s control including, without limitation, accident, alteration, misuse, abuse, neglect, negligence
(other than Manufacturer’s), failure to install, maintain, assemble, or mount the InSinkErator Product in accordance
with Manufacturer’s instructions or local electrical and plumbing codes.
• Wear and tear expected to occur during the normal course of use, including without limitation, cosmetic rust,
scratches, dents or comparable and reasonably expected losses or damages.
In addition to the above exclusions, this warranty does not apply to InSinkErator Products installed in a commercial or industrial
application.
No Other Express Warranty Applies
This warranty is the sole and exclusive warranty provided to the Customer identified above. No other express warranty, written or
verbal, applies. No employee, agent, dealer, or other person is authorized to alter this limited warranty or make
any other warranty on behalf of Manufacturer. The terms of this warranty shall not be modified by the Manufacturer, the original
owner, or their respective successors or assigns.
What we will do to Correct Problems
If your InSinkErator Product does not operate in accordance with the documentation provided to you, or you have questions
concerning your InSinkErator Product or how to determine when service is needed, please see attached Service Agency List.
The following information must be provided as part of your warranty claim: your name, address, phone number, your InSinkErator
Product model and serial number, and if necessary, upon request, written confirmation of either: (a) the date shown on your
installation receipt, or (b) the date shown on your purchase receipt.
Manufacturer or its authorized service representative will determine, in its sole and absolute discretion, if your InSinkErator
Product is covered under this warranty. You will be given the contact information for your closest authorized InSinkErator Service
Center. Please contact your InSinkErator Service Center directly to receive in home warranty repair or replacement service. Only
an authorized InSinkErator service representative may provide warranty service. InSinkErator is not responsible for warranty
claims arising from work performed on your InSinkErator Product by anyone other than an authorized InSinkErator service
representative.
If a covered claim is made during the Warranty Period, Manufacturer will, through its authorized service representative, either
repair or replace your InSinkErator Product. Cost of replacement parts or a new InSinkErator Product, and cost of labor for repair
or installation of the replacement InSinkErator Product are provided at no cost to you. Repair or replacement shall be determined
by Manufacturer or its authorized service representative in their sole discretion. All repair and replacement services will be
provided to you at your home. If Manufacturer determines that your InSinkErator Product must be replaced rather than repaired,
the warranty on the replacement InSinkErator Product will be limited to the unexpired term remaining in the original Warranty
Period.
Limitation of Liability
TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL MANUFACTURER OR ITS AUTHORIZED SERVICE
REPRESENTATIVES BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING
ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE
INSINKERATOR PRODUCT OR THE MANUFACTURER’S OR ITS AUTHORIZED SERVICE REPRESENTATIVE’S NEGLIGENCE.
MANUFACTURER SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT,
REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT,
NEGLIGENCE, STRICT LIABILITY, OTHER SORT OR OTHERWISE), SHALL MANUFACTURER’S LIABILITY TO YOU EXCEED
THE PRICE PAID BY THE ORIGINAL OWNER FOR THE INSINKERATOR PRODUCT.
The term "consequential damages" shall include, but not be limited to, loss of anticipated profits, business interruption, loss of
use or revenue, cost of capital or loss or damage to property or equipment.
WARRANTY INFORMATION
Replace filter cartridge when there is an obvious
decrease in water flow to the faucet or if there is an
objectionable taste or odor to the water.
When the inlet and outlet ports have been closed
and the filter’s internal pressure has been relieved,
water (about 60ml) will discharge from vent line.
If the new filter cartridge cannot be inserted, insert
the old one and turn until it stops, remove it and then
retry the new cartridge.
The disposable filter cartridge MUST be replaced
every 6 months, at the rated capacity or sooner if a
noticeable reduction in flow rate occurs.
FILTER GUIDE AND REPLACEMENT
Filter replacement instructions:
Replace with an InSinkErator
®
filter.
Place pan or dish towel under the filter to
catch water drainage during change.
Slowly turn the cartridge counter-clock-
wise completely until it stops (1/4 turn).
Pull cartridge straight down and discard.
Insert new cartridge into filter head.
Top surface of cartridge will become flush
with the bottom of the filter head when
fully engaged.
Turn the cartridge clockwise until it stops
(1/4 turn).
Open tap to expel trapped air.
Run water for 3 minutes before usage.
To Next Page
Loading...
Need help?
General
