Emerson ROC364 - Index

ROC364 Instruction Manual
I-1 Index Rev Jun/05
INDEX
Numerics
12-volt power................................................................ 1-5
24-volt power................................................................ 1-5
A
AGA .............................................................................B-6
AGA Point Displays ...................................................B-14
Display 1................................................................B-15
Display 2................................................................B-16
Display 3................................................................B-16
Alarm Code Bits.......................................B-9, B-10, B-11
Analog Inputs
Alarm Code Bits ......................................................B-9
Differential............................................................... 3-2
Differential Wiring................................................... 3-7
Loop......................................................................... 3-2
Loop Wiring............................................................. 3-6
Point Display............................................................B-8
Point Display Parameters.........................................B-9
Source...................................................................... 3-2
Source Wiring.......................................................... 3-8
Troubleshooting..................................................... 3-22
Analog Outputs
Alarm Code Bits ....................................................B-10
Analog Outputs to Analog Inputs.............................C-1
AO Source to AI Differential as Current Loop........C-1
AO Source to AI Differential as Voltage Input ........C-2
AO Source to AI Loop as Current Loop ..................C-1
AO Source to Ammeter............................................C-2
AO Source to Voltmeter...........................................C-2
Checking Voltage Source Installations................... 3-23
Point Display..........................................................B-10
Point Display Parameters.......................................B-10
Source...................................................................... 3-2
Source Wiring.......................................................... 3-9
Troubleshooting..................................................... 3-22
Antenna......................................................................... 1-4
Attenuation Levels
Communications Cards.......................................... 4-11
AUTO...........................................................................B-5
AUX OUT 1 ............................................................... 2-13
AUX OUT 2 ............................................................... 2-13
AUX PWR OUT 1...................................................... 2-10
AUX PWR OUT 2...................................................... 2-10
Auxiliary Discrete Output............................................. 2-4
Auxiliary Outputs ....................................................... 2-11
Auxiliary Power Wiring.............................................. 2-10
B
B1
Battery.................................................................... 2-14
Backplate...................................................................... 2-6
Dimensions.............................................................. 2-6
Installation ............................................................... 2-6
Mounting the I/O Module Rack............................... 2-8
Mounting the MCU to a Backplate.......................... 2-7
Backup Procedure
RAM...................................................................... 2-13
Battery
Replacing............................................................... 2-18
Verify Voltage ........................................................ 2-14
C
Calibration
I/O Modules............................................................. 3-5
RTD Module.......................................................... 3-17
Class I........................................................................... 1-5
Clock
Battery ................................................................... 2-14
Cold Start.................................................................... 2-16
COM1........................................................................... 4-1
COM2........................................................................... 4-1
Communications
Verifying the ROC can Communicate with the PC
......................................................................... 2-15
Wiring Operator Interface.......................................2-11
Communications Cards................................................. 4-1
Attenuation Levels..................................................4-11
Dial-up Modem........................................................ 4-7
EIA-232 (RS-232) ................................................... 4-2
EIA-422/485 (RS-422/485) ..................................... 4-4
Jumpers.................................................................. 4-10
Leased-Line Modem................................................ 4-6
LED Indicators......................................................... 4-3
Radio Modem .......................................................... 4-5
Specifications......................................................... 4-21
Troubleshooting..................................................... 4-19
Wiring.................................................................... 4-12
Configuration
I/O Point ................................................................ 3-28
Connecting
Auxiliary Power Wiring......................................... 2-10
Communications Wiring.........................................2-11
Ground Wiring......................................................... 2-9
Main Power Wiring................................................ 2-10
Connectors
J1 ........................................................................... 5-2
P7 .............................................................4-5, 4-6, 4-7
CTS............................................................................... 4-3
Current Loop
AO Source Module to AI Differential Module........C-1
AO Source Module to AI Loop Module ..................C-1
AO Source to Ammeter............................................C-2