Emerson ROC364 - Page 142

ROC364 Instruction Manual
I-3 Index Rev Jun/05
Figure 3-23. RTD Input Module Field Wiring for Three-
Wire RTDs ................................................................ 3-19
Figure 3-24. RTD Input Module Field Wiring for Four-
Wire RTD With Compensation Loop........................ 3-20
Figure 3-25. Field Wiring for Four-Wire, Single Element
RTD........................................................................... 3-20
Figure 3-26. Field Wiring for a HART Interface Module
.................................................................................. 3-21
Figure 4-1. EIA-232 (RS-232) Serial Communications
Card............................................................................. 4-2
Figure 4-2. EIA-422/485 (RS-422/485) Serial
Communications Card................................................. 4-4
Figure 4-3. Radio Modem Communications Card....... 4-5
Figure 4-4. Leased-Line Modem Communications Card
.................................................................................... 4-6
Figure 4-5. Dial-up Modem Communications Card –
New............................................................................. 4-7
Figure 4-6. Dial-up Modem Communications Card.... 4-8
Figure 4-7. Phone Jack Location ................................. 4-9
Figure 4-8. Location of LED Identification Decal..... 4-10
Figure 4-9. Location of Attenuation Resistor............. 4-11
Figure 4-10. EIA-232 (RS-232) Wiring Schematic ... 4-13
Figure 4-11. EIA-422 (RS-422) Wiring Schematic ... 4-14
Figure 4-12. EIA-485 (RS-485) Wiring Schematic ... 4-14
Figure 4-13. Radio Modem Wiring Schematic.......... 4-15
Figure 4-14. Leased-Line Modem Wiring Schematic
.................................................................................. 4-17
Figure 4-15. Dial-Up Modem Wiring Schematic....... 4-18
Figure 5-1. I/O Converter Card.................................... 5-1
Figure A-1. Lightning Protection Module................... A-1
Figure B-1. Local Display Panel..................................B-1
Figure B-2. LDP Parts Orientation ..............................B-2
Figure B-3. LCD Sub-Assembly .................................B-3
Figure B-4. LCD Inside View of Door ........................B-3
Figure B-5. LCD RTV Installation ..............................B-4
Figure B-6. Typical Main Menu Display.....................B-5
Figure B-7. I/O Menu Display.....................................B-6
Figure B-8. Discrete Input Point Display.....................B-7
Figure B-9. Discrete Output Point Display..................B-8
Figure B-10. Analog Input Point Display....................B-8
Figure B-11. Analog Input Alarm Code Bits ...............B-9
Figure B-12. Analog Output Point Display................B-10
Figure B-13. Analog Output Alarm Code Bits...........B-10
Figure B-14. Pulse Input Point Display.....................B-11
Figure B-15. Pulse Input Alarm Code Bits ................B-11
Figure B-16. SYS Parameter Display 1.....................B-12
Figure B-17. SYS Parameter Display 2.....................B-12
Figure B-18. SYS Parameter Display 3.....................B-13
Figure B-19. SYS Parameter Display 4.....................B-13
Figure B-20. DB Menu Display.................................B-14
Figure B-21. DB Point Display..................................B-14
Figure B-22. AGA Menu Display..............................B-15
Figure B-23. AGA Point Display 1............................B-15
Figure B-24. AGA Point Display 1 Alarm Code Bits
..................................................................................B-15
Figure B-25. AGA Point Display 2............................B-16
Figure B-26. AGA Point Display 3............................B-16
Figure B-27. Plate Change Password Display...........B-17
Figure B-28. Select AGA Point Display ....................B-17
Figure B-29. Time Out Display .................................B-18
Figure B-30. Time Remaining Display......................B-18
Figure B-31. Plate Size Editing Displays ..................B-18
Figure B-32. Write to EEPROM Display ..................B-18
Figure B-33. PID Point Display.................................B-19
Figure B-34. FST Point Display ................................B-19
Figure B-35. MSG Point Display ..............................B-20
Figure B-36. LCD Menu Display..............................B-20
Figure B-37. LCD Point Display...............................B-21
Figure B-38. LCD Point Display – EDIT..................B-21
Figure B-39. Parameter Editing Display....................B-21
Figure B-40. Write to EEPROM Display ..................B-22
Figure C-1. Current Loop — AO Source Module to AI
Loop Module...............................................................C-1
Figure C-2. Current Loop — AO Source Module to AI
Differential Module ....................................................C-1
Figure C-3. Voltage Input — AO Source Module to AI
Differential Module ....................................................C-2
Figure C-4. Current Loop — AO Source Module to
Ammeter .....................................................................C-2
Figure C-5. Voltage Output — AO Source to Voltmeter
....................................................................................C-2
Figure C-6. DO Source Module to DI Isolated Module
....................................................................................C-3
Figure C-7. DO Isolated Module to DI Source Module
....................................................................................C-3
Figure C-8. DO Source Module to PI Isolated Module
....................................................................................C-3
Figure C-9. DO Isolated Module to PI Source Module
....................................................................................C-4
Figure C-10. Potentiometer Input to AI Loop Module
....................................................................................C-4
Figure C-11. Potentiometer Input to AI Differential
Module........................................................................C-4
Figure C-12. Switch Input to DI Isolated Module.......C-5
Figure C-13. Switch Input to DI Source Module.........C-5
Figure C-14. Switch to PI Source Module...................C-5
Figure C-15. Switch to PI Isolated Module.................C-6
Firmware.....................................................................B-12
Flash Memory Save Configuration............................. 2-13
FlashPAC...................................................................... 2-3
Determining Version................................................ 2-4
Installation ............................................................... 2-9
Replacing............................................................... 2-16
Frequency Shift Keyed
FSK.......................................................................... 4-5
FST...............................................................................B-6
Function Sequence Table.......................................B-19
Point Display .........................................................B-19
Function Keys...............................................................B-4
Fuses...........................................................2-3, 2-10, 2-14
G
Gauges of Wire........................................................... 2-10
GND .................................................................. 2-10, 4-10
Ground Wiring.............................................................. 2-9
Grounding
Requirements........................................................... 1-6