How to fix emmeti EH0618DC that does not start re-operation immediately?
After stopping, the emmeti Heat Pump will not restart immediately for approximately 3 minutes. This is to protect the system.
Details the physical dimensions of the unit.
Lists relevant European directives and their numbers for compliance.
Presents detailed technical specifications for various models and applications.
Explains circulator speed levels and provides flow rate/power graphs for models.
Shows graphical representations of heating and cooling operating ranges based on air and water temperatures.
Describes packaging details, handling symbols, and packing dimensions for different models.
Explains the unit's rating label and details the unpacking process and safety.
Provides safety information, first aid, firefighting, and exposure control for R32 refrigerant.
General warnings, prohibited actions, and safety symbol meanings for installation and use.
Specifies prohibitions and warnings related to the installation process.
Details minimum operating spaces, fixing methods, and condensate drainage pipes.
Explains hydraulic connections, provides a system scheme, and gives recommendations for the circuit.
Crucial warnings for operation, anti-freeze function, and water quality requirements.
Step-by-step instructions for filling the hydraulic circuit and removing air.
Provides instructions and warnings for electrical connections and safety, including earthing.
Detailed instructions on connecting wiring to terminal blocks, including cautions.
Details electrical connections for Recipe 1 configuration, showing diagrams and terminal block assignments.
Lists configurable parameters for Recipe 1 and specifies PCB connections for probes and inputs.
Details electrical connections for Recipe 2 configuration, showing diagrams and terminal block assignments.
Lists configurable parameters for Recipe 2 and specifies PCB connections for probes and inputs.
Details electrical connections for Recipe 3 configuration, showing diagrams and terminal block assignments.
Lists configurable parameters for Recipe 3 and specifies PCB connections for probes and inputs.
Details electrical connections for Recipe 10 (Febos-Crono Master) configuration.
Lists configurable parameters for Recipe 10 and specifies PCB connections for probes and inputs.
Details electrical connections for Recipe 13 (ECO HYDRO KIT) configuration.
Lists configurable parameters for Recipe 13 and specifies PCB connections for probes and inputs.
Shows the hydraulic connection diagram for Radiant system + Fancoil + Eco Hot Water.
Shows the electrical connection diagram for Recipe 1.
Shows the hydraulic connection diagram for Radiant system + Fancoil + Boiler x DHW.
Shows the electrical connection diagram for Recipe 1.
Shows the hydraulic connection diagram for Radiant system + Fancoil + ECO HYDRO KIT + Boiler.
Shows the electrical connection diagram for Recipe 2.
Shows the hydraulic connection diagram for Radiant system + Fancoil + ECO HYDRO KIT + Boiler + FEBOS-CHRONO + DEHUMIDIFIER.
Shows the electrical connection diagram for Recipe 10.
Explains the Smart-MT controller's display, keys, and their functions.
Details key operations in the main screen and the procedure for setting the password.
Guides on accessing and changing parameters within the "Set" menu.
Provides instructions for setting the date and time on the Smart-MT controller.
Lists service parameters related to remote consents and analogue inputs.
Lists service parameters for ambient settings, signals, and physical output status.
Lists service parameters for heat pump status, counters, and system configurations.
Lists service parameters for system configurations, including heat pump settings.
Lists service parameters for water temperature settings for compressor frequency adjustment.
Lists service parameters for ambient settings, signals, and compressor steps.
Lists service parameters for DHW production, frost protection, and additional heater settings.
Lists service parameters for alarm history.
Explains how to turn the heat pump on and off using the Febos-Crono system.
Describes how to select heating or cooling mode via Febos-Crono.
Explains how ambient thermostat consent affects heat pump operation.
Guides on setting water temperatures and adjusting them using climate curves.
Explains how to set consent for Set Point 2 and Fancoil operation.
Details when the heat pump circulator is activated automatically.
Explains compressor modulation and how to limit frequency via external signal.
Details how to heat domestic hot water using the heat pump or Eco Hot Water.
Instructions for DHW heating with Eco Hot Water, Heat Pump, PdC addition, and electric heater.
Explains relaunch circulator function and how the heat pump manages additional heater consent.
Explains parallel, alternate, and alarm-driven operation with additional generators.
Explains frost protection mechanisms and the importance of the external temperature sensor.
Explains water flow rate monitoring, alarms, and connections for different flow meters.
Covers electrical power monitoring and various dehumidifier operation modes.
Guides on accessing alarms, history, and configuring system alarm inputs.
Provides a troubleshooting guide for common issues and checks.
Lists alarm codes, their descriptions, and corresponding solutions.
Explains how to manually reset protection status after an alarm.
Lists alarm codes displayed on the PCB and their troubleshooting steps.
Lists error codes related to discharge temperature, current, and CT disconnect.
Lists error codes related to compressor rotation, sensors, and fuses.
Lists error codes related to motor fans, PCB errors, and installation.
Lists error codes for SMART-MT serial error, power supply, and temperature sensors.
Lists error codes for high pressure switch, compressor over-temperature, and cooling/heating issues.
Explains how to perform voltage, resistance, and continuity checks on the main PCB.
Illustrates how to check fuse continuity and measure fan motor voltage on the main PCB.
Provides diagrams for measuring fan motor and pump voltages on the main PCB.
Illustrates how to check the resistance of 4-way valves, defrost heater, and compressor.
Explains how to display and delete historical errors and access data display mode.
Provides resistance values for various temperature sensors at different temperatures.
Provides warnings and instructions for cleaning the heat pump, including what not to use.
Explains how to check water condensate drainage and when to contact service.
Wiring diagram for the EH0618DC model, showing PCB connections and safety warnings.
Wiring diagram for the EH1018DC model, showing PCB connections and safety warnings.
Wiring diagram for the EH1218DC model, showing PCB connections and safety warnings.
Wiring diagram for the EH1618DC model, showing PCB connections and safety warnings.
Wiring diagram for the EH1718D3 model, showing PCB connections and safety warnings.
Product fiche details for EH0618DC model, including energy efficiency and technical data.
Product fiche details for EH1018DC model, including energy efficiency and technical data.
Product fiche details for EH1218DC model, including energy efficiency and technical data.
Product fiche details for EH1618DC model, including energy efficiency and technical data.
Product fiche details for EH1718D3 model, including energy efficiency and technical data.
Details warranty coverage, exclusions for negligence, improper installation, and wear.
Covers reporting faults, replacement units, and payment terms related to warranty.
To Next Page
General
