What to do if emmeti EH1718D3 shows AL09 error (Water flow rate to the HP too low)?
If the emmeti Heat Pump displays error code AL09 indicating a low water flow rate, first check the pressure and water circulation within the system. Secondly, inspect the water filter and clean it if necessary.
What to do if emmeti Heat Pump shows AL07 error (Low water temp value)?
If the emmeti Heat Pump displays error code AL07 indicating a low water temperature, first check the pressure and water circulation in the system. Second, manually reset the HP by switching it off and on again after a few minutes, then monitor its operation.
What to do if emmeti Heat Pump shows AL10 error (Low system pressure)?
If the emmeti Heat Pump displays error code AL10 indicating low system pressure, check the water pressure in the system.
What to do if emmeti Heat Pump shows AL01 error (Abnormal value of the water inlet temp to the HP)?
If the emmeti Heat Pump displays error code AL01 indicating an abnormal water inlet temperature, first check the sensor connection to the PCB TERMINAL BLOCK. If the issue persists, replace the sensor. If the problem still occurs, replace the SMART-MT.
What to do if emmeti EH1718D3 shows AL12 error (Abnormal value of the AMBIENT Temp. From Febos Chrono)?
If the emmeti Heat Pump displays error code AL12, indicating an abnormal ambient temperature from Febos Chrono, follow these steps: 1. Check the connection of the humidity sensor to the FEBOS CRONO MASTER (if AL13). 2. Check the connection of the FEBOS CRONO MASTER to the PCB TERMINAL BLOCK. 3. Replace the FEBOS CRONO MASTER. 4. Replace the SMART-MT.
What to do if emmeti EH1718D3 shows AL11 error (Failed / incorrect communication with Febos Crono (Master))?
If the emmeti Heat Pump displays error code AL11 indicating a communication failure with Febos Crono (Master), follow these steps: 1. Check the connection of the Febos Crono Master to the PCB TERMINAL BLOCK. 2. Replace the Febos Chrono Master. 3. Replace the SMART-MT.
What to do if emmeti Heat Pump shows AL14 error (Stagione incongruente (SMART-MT / Febos-Crono))?
If the emmeti Heat Pump displays error AL14, which indicates 'Stagione incongruente', change the season setting on Febos-Crono or entrance 104 (G+ / G-) della PCB TERMINAL BLOCK.
Why is the pump running while my emmeti EH1718D3 is stopped?
The circulation pump operates automatically at times to prevent scale build-up on the pipe walls or for antifreeze protection.
What to do if I hear the sound of water in the pipes of my emmeti EH1718D3?
To resolve the sound of water in the pipes of your emmeti Heat Pump, vent the air from the system and refill it with water.
Why does steam escape from my emmeti EH1718D3?
Steam escaping from the emmeti Heat Pump is caused by the unit defrosting during heating operation.
Provides detailed technical specifications for various operating conditions.
Safety information, properties, first aid, fire fighting, and disposal of R32 refrigerant.
General prohibitions and dangers related to unit operation and installation.
Specific prohibitions and warnings for installing the heat pump safely.
Covers hydraulic connections, water charge, electrical system, and wiring.
Guide to accessing and changing parameters, and setting the system time.
Parallel/alternate operation, alarms, electrical power monitoring, and error handling.
General troubleshooting steps for common unit problems.
Detailed list of SMART-MT alarm codes and manual reset procedures.
PCB alarm codes related to electrical supply, fuses, voltage, and sensors.
PCB alarm codes for motors, PCB errors, and system malfunctions.
Procedures for testing fuses, fan motor, and pump voltages.
Detailed wiring diagram for the EH0618DC model.
Detailed wiring diagram for the EH1018DC model.
To Next Page
General
