ENFORCER Auto Dialer
16 SECO-LARM U.S.A., Inc.
Auto dialer will not arm/disarm
Make sure that you have entered the correct PIN
Number. Try re-entering it.
• While pressing and holding the [PROG] button, use a
pen or paper clip to press the [RESET] button on the
back of the dialer. This sets the PIN number to the
default (000).Then try to arm/disarm again.
Auto dialer will not dial out
Make sure that the telephone line is working.
• Make sure that you have programmed at least one
telephone number into the unit and that the full
number has been stored.
• Make sure that the system is in Auto Dial mode.
Unit doesn’t respond to a call-back
Check to see if another unit (fax or answering
machine) could be answering the call and remove the
other unit.
• Adjust the call-in ring detect setting so that the auto
dialer will answer.
Difficulty in activating ‘room monitor’
by telephone remote control
Try pressing the code key again.
• Move to a quieter location as ambient noise may
affect the auto dialer’s ability to detect the tone signal.
The information and specifications printed in this manual are current at the time of publication.
However, the SECO-LARM policy is one of continual development and improvement. For this reason,
SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible
for misprints or typographical errors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or
d, in whole or in part, without the written permission of SECO
LARM product is warranted against defects in material and workmanship while
used in normal service for one (1) year from the date of sale to the original customer. SECO-
obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation
prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical
or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation,
or if for any other reason SECO-
LARM determines that such equipment is not operating properly as a result
of causes other than defects in material and workmanship. The sole obligation of SECO-
purchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECO-
no event shall SECO-
LARM be liable for any special, collateral, incidental, or consequential personal or
erty damage of any kind to the purchaser or anyone else.
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Users and installers of this product are responsible for ensuring this product complies with all
national, state, and local laws and statutes related to monitoring and recording audio and video signals.
SECO-LARM will not be held responsible for the use of this product in violation of any current laws or
While the system can provide valuable protection to home and property when properly installed, it
cannot guarantee complete protection against intrusion. SECO-LARM is not responsible for any losse
damage which may occur during the use of this product.
®
Auto Dialer
Manual
When triggered by an alarm system, the ENFORCER Auto Dialer can call up to 5 numbers. Each
number can contain up to 32 digits, including #, tones, and pauses. The LCD shows the number being
dialed at each stage of the dialing process. The receiver can then listen in to sounds in the room and
disarm the system. The same functions are available by remote call in as well as arming the system.
The dialer includes a home mode (acting like a door chime when the owner is present) and a panic
button. The 105dB built-in siren alarm can be programmed on or off. It also allows for the option of a
backup battery (not included) to continue offering protection during a power
loss and uses flash memory
to protect against system data loss in case of extended power failure.
E-921APQ
E-921GPQ
To Next Page
Need help?
General
