EnGenius ECB350 Quick Installation Guide

Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com
Disclaimer: Information may be subject to changes without prior notication.
Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
ECB350
Package content
Unpack the box and verify the content:
- ECB350
- RJ-45 Ethernet-cable
- 12V/1A 100V~240V Power adaptor
- Quick Installation Guide
- CD with instruction manual
Setting up the ECB350
After verifying the contents of the box, continue on to setting up the ECB350.
Hardware installation
1. Ensure that the computer in use has an Ethernet card (RJ-45 Ethernet port).
For more information, verify with the user manual.
2. Connect one end of the Cat5e Ethernet cable into RJ-45 port of the ECB350
and the other end to the RJ-45 port in the computer that will use the ECB350.
Ensure that the cable is securely connected to both the ECB350 and the
computer.
3. Connect the power adaptor DC inlet to the DC-IN port of the ECB350 and
the power adapter in the electrical outlet.
Computer setup
1. After ensuring the EnGenius device is powered on and plugged in, ensure
that your computer is on.
2. For the next steps, refer to your ‘operating system’-user manual.
3. Once your computer is on, ensure that your TCP/IP is set to ON or
ENABLED. In the control panel, double click network connections and then
double click on the connection of your Network Interface Card (NIC). Select
Internet Protocol (TCP/IP) and then click on the properties button.
4. If your PC is already on a computer network, ensure that you have set it to
a Static IP adress on the interface (or Ethernet card that will use the ECB350).
Set it as 192.168.1.21 and the subnet mask address as 255.255.255.0.
Select ‘Use the following IP address’-radio button. Once the computer has been
prepared, proceed to setting up the ECB350.
EAP350 setup
1. To configure the ECB350, open a web browser (example: Microsoft Internet
Explorer, Mozilla Firefox, Google Chrome, etc.)
2. In the adress bar of the web browser, enter: 192.168.1.1 (the default IP
address of the ECB350)and hit ENTER.
3. A login screen will appear. By default, the username of the ECB350 is
admin and the password is admin. Enter the current username and password
of the ECB350 and then click ‘Login’. Refer to the ECB350 user manual on
how to change the username and password.
4. After clicking ‘Login’ with the correct username an password, the ECB350
main menu will appear. If you are successful, proceed to setting up the wireless
connection.
PC
Ethernet
Access Point
AC/DC cable
Power Outlet

EnGenius ECB350 Specifications

General

Frequency band	2.4 - 2.484 GHz
Channels quantity	11 channels
Networking standards	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.1Q, IEEE 802.3af
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	300 Mbit/s
Quality of Service (QoS) support	Yes
Antenna features	Detachable antenna
Antennas quantity	2
Antenna connector type	SMA
Antenna gain level (max)	5 dBi
Internal	No
Certification	FCC, CE, IC
WAN connection	Ethernet (RJ-45)
Security algorithms	128-bit WEP, 64-bit WEP, SSID, WPA-AES, WPA-EAP, WPA-PSK, WPA-TKIP
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 50 °C
Operating relative humidity (H-H)	0 - 90 %
Power requirements	12V / 1A
Flash memory	8 MB
Internal memory	32 MB

Weight and Dimensions

Weight	280 g
Dimensions (WxDxH)	105 x 135 x 30 mm