EnGenius ENS202EXT Quick Installation Guide

Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com
Disclaimer: Information may be subject to changes without prior notication.
Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
ENS202EXT
Package content
Unpack the box and verify the content:
- ENS202EXT
- PoE injector
- Power adapter
- Quick Start Guide
- Wall mount screw set
- 2* Pole mounting strap
Minimum requirements
- Broadband Internet Service (cable or DSL modem)
- Internet browser (Internet Explorer, Safari, Firefox, Chrome)
Connecting the ENS202EXT
1. Remove the rear bottom panel.
2. Connect one end of the Ethernet cable into the LAN(PoE) port of the
ENS202EXT and the other end to the PoE Ethernet port on the PoE injector.
3. Connect the power adapter to the DC-IN port of the ENS202EXT and plug
the other end into an electrical outlet.
4. Connect the second Ethernet cable into the LAN port of the PoE injector and
the other end to the Ethernet port on the computer.
5. Place the panel removed from step 1 back into the device.
Note: The ENS202EXT should ONLY be powered via Ethernet cable connected
to the included PoE Injector.
Computer setup
1. After ensuring the EnGenius device is powered on and plugged in, ensure
that your computer is on.
2. For the next steps, refer to your ‘operating system’ user manual.
3. Once your computer is on, ensure that your TCP/IP is set to ‘ON’ or
‘ENABLED’. In the control panel, double click network connections and then
double click on the connection of your Network Interface Card (NIC). Select
Internet Protocol (TCP/IP) and then click on the properties button.
4. If your PC is already on a computer network, ensure that you have set it to a
Static IP adress on the interface (or Ethernet card that will use
the ENS202EXT). Set it as 192.168.1.21 and set the subnet mask-address as
255.255.255.0. Select ‘Use the following IP address’-radio button. Once the
computer has been prepared, proceed to setting up the ENS202EXT.

EnGenius ENS202EXT Specifications

General

5 GHz	No
Modulation	16-QAM, 64-QAM, BPSK, OFDM, QPSK
Frequency band	2.4 GHz
Operating modes	Access Point (AP), Client Bridge, Client Router, Repeater, WDS
Channel bandwidth	40 MHz
Transmitting power	15 dBmW
Networking standards	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.1x
Virtual LAN features	Tagged VLAN
Spread spectrum method	DSSS
Ethernet LAN data rates	10, 100 Mbit/s
Maximum data transfer rate	300 Mbit/s
Quality of Service (QoS) support	Yes
Supported data transfer rates	1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48, 54, 300Mbps
Antenna features	Detachable antenna
Antennas quantity	2
Antenna direction type	Omni-directional
Antenna gain level (max)	5 dBi
Placement	Wall
Product color	White
International Protection (IP) code	IP55
Interface	LAN, WLAN
USB 2.0 ports quantity	0
Security algorithms	802.1x RADIUS, WPA, WPA2
Number of SSID supported	4
Storage temperature (T-T)	-30 - 80 °C
Operating temperature (T-T)	-20 - 70 °C
Operating relative humidity (H-H)	0 - 90 %
AC input voltage	24 V
Flash memory	16 MB
Internal memory	64 MB
Package depth	309.88 mm
Package width	71.12 mm
Package height	233.68 mm
Package weight	725.7 g
Harmonized System (HS) code	85176990

Weight and Dimensions

Depth	185.42 mm
Width	99 mm
Height	28.95 mm
Weight	317.5 g