Epson EX3200 User Manual

96 Solving Problems
Error light(s) status
Error light(s) status Description
P Green or orange
Flashing orange
Off
It’s time to replace the lamp. See page 86 for instructions. If you continue to
use the lamp after the replacement warning, there is an increased possibility
that the lamp may break.
P Flashing red
Off
Flashing orange
Rapid cooling is in progress. Although this is not an abnormal condition,
projection will stop automatically if the temperature rises higher. Make sure
there is plenty of space around and under the projector for ventilation, and that
the air filter and vents are clean.
P Red
Off
Red
The projector is overheating, which turns the lamp off automatically. Wait until
the projector switches to standby mode (about 5 minutes). Make sure there is
plenty of space around and under the projector for ventilation.
The air filter may be clogged. Clean or replace the air filter as described on
pages 84 to 86.
If you’re using the projector above an altitude of 4,921 feet (1,500 meters), turn
on High Altitude Mode in the Operation menu (see page 76).
If the projector continues to overheat after you clean the air filter, stop using
the projector, disconnect the power cord, and contact Epson for help as
described on page 104.
Warning: Except as specifically explained in this User’s Guide, do not attempt
to service this product yourself.
P Flashing red
Red
Flashing red
The projector has an internal problem. Stop using the projector, disconnect the
power cord, and contact Epson for help, as described on page 104.
P Red
Off
Flashing red
There is a problem with the fan or temperature sensor. Stop using the
projector, disconnect the power cord, and contact Epson as described on
page 104.
P Red
Flashing red
Off
The lamp may be burnt out. First make sure the lamp cover is securely
installed. If that’s not the problem, the air filter may be clogged. Clean or
replace the air filter as described on pages 84 to 86.
If this does not resolve the problem, let the lamp cool and then remove it. If the
lamp is cracked, replace it as described on page 86. If the lamp is not cracked,
reinstall it. If reinstalling doesn’t work, replace the lamp.
If you’re using the projector above an altitude of 4,921 feet (1,500 meters), turn
on High Altitude Mode in the Operation menu (see page 76).
If none of these suggestions resolves the problem, contact Epson as described
on page 104.
P Flashing red
Flashing red
Flashing red
The projector has an Auto Iris error or power error. Stop using the projector,
disconnect the power cord, and contact Epson for help, as described on
page 104.

Epson EX3200 Specifications

Projection Specifications

pixel number	480, 000 dots (800 x 600) x 3
white light output	2600 lumens
color light output	2600 lumens
aspect ratio	4:3
native resolution	800 x 600 (SVGA)
contrast ratio	Up to 2000:1
color reproduction	16.77 million colors
lamp type	200 W UHE
lamp life in ECO Mode	Up to 5000 hours
lamp life in Normal Mode	Up to 4000 hours
throw ratio range	1.45 – 1.96
size projected distance	30" – 350" (0.76 – 8.90 m)
keystone correction vertical	± 30 degrees

Lens Specifications

f-number	1.44
focal length	16.6 mm
zoom ratio	Digital zoom 1.0 – 1.3

Power and Noise

power supply voltage	100 – 240 V ±10%, 50/60 Hz
power consumption	280 W
power consumption power off	0.3 W
fan noise normal mode	37 dB
fan noise ECO mode	29 dB

Operating Environment

operating temperature	41 ˚ to 95 ˚F (5 ˚ to 35 ˚C)
operating angle right/left	± 30 degrees
operating angle upper/lower	± 15 degrees
operating distance	19' (6 m)

Dimensions and Weight

dimensions including feet	11.6" x 9.0" x 3.1"
dimensions excluding feet	11.6" x 9.0" x 3.0"
weight	5.1 lb/2.3 kg