EasyManuals Logo

Epson PowerLite S27 User Manual

Epson PowerLite S27
242 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #48 background imageLoading...
Page #48 background image
If you must set addresses manually, turn off DHCP and enter the projector's IP Address, Subnet
Mask, and Gateway Address as needed.
Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on
the remote control. To select a highlighted number, press Enter.
10. To prevent display of the IP address on the standby screen, turn off IP Address Display.
11. When you finish selecting settings, select Complete and follow the on-screen instructions to save
your settings and exit the menus.
Parent topic: Wired Network Projection
Wireless Network Projection
You can send images to your projector through a wireless network. To do this, you must install the
Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless
projection.
Note: The wireless LAN module is not included with your projector and is optional.
Note: If your projector is connected via a LAN cable to a network that includes a wireless access point,
you can connect to the projector wirelessly using the EasyMP Network Projection software.
There are two ways to connect the projector to your wireless network:
Using the optional Quick Wireless Connection USB Key (Windows only)
Configuring the connection manually using the projector's Network menus
After installing the module and setting up the projector, install the network software from the Epson
Projector Software CD or download the software, as necessary. Use the following software and
documentation to set up, control, and monitor wireless projection:
EasyMP Network Projection software sets up your computer for wireless network projection. See the
EasyMP Network Projection Operation Guide for instructions.
EasyMP Monitor software (Windows only) lets you monitor and control your projector through the
network. You can download the latest software and documentation from the Epson web site. Go to
epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector.
EasyMP Multi PC Projection software allows you to hold interactive meetings by projecting the
computer screens of users over a network. See the EasyMP Multi PC Projection Operation Guide for
instructions.
48

Table of Contents

Other manuals for Epson PowerLite S27

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Epson PowerLite S27 and is the answer not in the manual?

Epson PowerLite S27 Specifications

General IconGeneral
Matrix size0.55 \
Matrix type3-panel (p-Si TFT active)
Number of colors1.073 billion colors
Native aspect ratio4:3
Projection distance1.77 - 2.4 m
Projection technology3LCD
Contrast ratio (typical)10000:1
Screen size compatibility30 - 350 \
Projection distance (tele)0 - 2.4 m
Projection distance (wide)0 - 1.77 m
Projector native resolutionSVGA (800x600)
Keystone correction, horizontal-30 - 30 °
Projector brightness (economic mode)1890 ANSI lumens
FocusManual
Throw ratio1.45 - 1.96:1
Focal length range16.9 - 20.28 mm
Aperture range (F-F)1.44 - 1.44
Lamp typeUHE
Lamp power200 W
Lamps quantity1 lamp(s)
Light source typeLamp
Service life of light source5000 h
Service life of light source (economic mode)10000 h
Full HDNo
Video processing10 bit
Analog signal format systemNTSC, NTSC 4.43, PAL, PAL 60, PAL M, PAL N, SECAM
Supported graphics resolutions1280 x 800, 1366 x 768, 1024 x 768 (XGA), 1280 x 1024 (SXGA), 1400 x 1050 (SXGA+), 1440 x 900 (WXGA+), 640 x 480 (VGA)
DC-in jackYes
USB connector typeUSB Type-A, USB Type-B
Serial interface typeRS-232
USB 2.0 ports quantity2
Ethernet LAN (RJ-45) ports-
Noise level37 dB
2D/3D frequency image50 - 85 Hz
Noise level (economic mode)29 dB
RMS rated power5 W
PlacementDesktop, Ceiling
Product typeStandard throw projector
Product colorWhite
Cable lock slot typeKensington
Power sourceAC
AC input voltage100 - 240 V
Voltage tolerance10 %
AC input frequency50 - 60 Hz
Power consumption (standby)0.21 W
Power consumption (typical)284 W
Power consumption (economy mode)208 W
Storage temperature (T-T)-10 - 60 °C
Operating temperature (T-T)5 - 35 °C
Storage relative humidity (H-H)10 - 90 %
Operating relative humidity (H-H)20 - 80 %
Sustainability certificatesRoHS
Weight and Dimensions IconWeight and Dimensions
Depth244 mm
Width297 mm
Height87 mm
Weight2500 g

Related product manuals