ESAB Cutmaster 60 - Page 36

ESAB CUTMASTER 60
OPERATION Manual 0-5402
4T-10
Type Torch: SL60 With Exposed Tip Type Material: Mild Steel
Type Plasma Gas: Air Type Secondary Gas: Single Gas Torch
Thickness Tip Output Amperage
Speed (Per
Minute)
Standoff
Plasma Gas
Press
Flow (CFH) Pierce
Pierce
Height
Inches
mm
(Cat.
No.)
Volts
(VDC)
(Amps) Inches Meters Inches mm psi* bar Plasma Total**
Delay
(Sec)
Inches mm
0.060
1.5 9-8210
110
60
290
7.37 0.19 4.8 75 5.2 90 245
0.00
0.19 4.8
0.075
1.9 9-8210
120
60
285
7.24 0.19 4.8 75 5.2 90 245
0.10
0.19 4.8
0.120
3.0 9-8210
120
60
180
4.57 0.19 4.8 75 5.2 90 245
0.10
0.19 4.8
0.135
3.4 9-8210
119
60
170
4.32 0.19 4.8 75 5.2 90 245
0.10
0.19 4.8
0.188
4.8 9-8210
121
60
100
2.54 0.19 4.8 75 5.2 90 245
0.20
0.19 4.8
0.250
6.4 9-8210
119
60
80
2.03 0.19 4.8 75 5.2 90 245
0.30
0.19 4.8
0.375
9.5 9-8210
124
60
50
1.27 0.19 4.8 75 5.2 90 245
0.50
0.19 4.8
0.500
12.7 9-8210
126
60
26
0.66 0.19 4.8 75 5.2 90 245
0.75
0.19 4.8
0.625
15.9 9-8210
127
60
19
0.48 0.19 4.8 75 5.2 90 245
NR NR NR
0.750
19.1 9-8210
134
60
14
0.36 0.19 4.8 75 5.2 90 245
NR NR NR
1.000
25.4 9-8210
140
60
6
0.15 0.19 4.8 75 5.2 90 245
NR NR NR
Type Torch: SL60 With Exposed Tip Type Material: Stainless Steel
Type Plasma Gas: Air Type Secondary Gas: Single Gas Torch
Thickness Tip Output Amperage
Speed (Per
Minute)
Standoff
Plasma Gas
Press
Flow (CFH) Pierce
Pierce
Height
Inches
mm
(Cat.
No.)
Volts
(VDC)
(Amps) Inches Meters Inches mm psi* bar Plasma Total**
Delay
(Sec)
Inches mm
0.06
1.5 9-8210
119
60
350 8.91
0.19 4.8 75 5.2 90 245
0.00
0.20 5.1
0.075
1.9 9-8210
116
60
300 7.64
0.19 4.8 75 5.2 90 245
0.10
0.20 5.1
0.120
3.0 9-8210
123
60
150 3.82
0.19 4.8 75 5.2 90 245
0.10
0.20 5.1
0.135
3.4 9-8210
118
60
125 3.18
0.19 4.8 75 5.2 90 245
0.10
0.20 5.1
0.188
4.8 9-8210
122
60
90 2.29
0.19 4.8 75 5.2 90 245
0.20
0.20 5.1
0.250
6.4 9-8210
120
60
65 1.65
0.19 4.8 75 5.2 90 245
0.30
0.20 5.1
0.375
9.5 9-8210
130
60
30 0.76
0.19 4.8 75 5.2 90 245
0.50
0.20 5.1
0.500
12.7 9-8210
132
60
21 0.53
0.19 4.8 75 5.2 90 245
0.75
0.20 5.1
0.625
15.9 9-8210
130
60
15 0.38
0.19 4.8 75 5.2 90 245
NR NR NR
0.750
19.1 9-8210
142
60
12 0.31
0.25 6.4 75 5.2 90 245
NR
NR NR
Type Torch: SL60 With Exposed Tip Type Material: Aluminum
Type Plasma Gas: Air Type Secondary Gas: Single Gas Torch
Thickness Tip Output Amperage
Speed (Per
Minute)
Standoff
Plasma Gas
Press
Flow (CFH) Pierce
Pierce
Height
Inches
mm
(Cat.
No.)
Volts
(VDC)
(Amps) Inches Meters Inches mm psi* bar Plasma Total**
Delay
(Sec)
Inches mm
0.060
1.5 9-8210
110
60
440
11.18 0.25 6.4 75 5.2 90 245
0.00
0.25 6.4
0.075
1.9 9-8210
110
60
440
11.18 0.25 6.4 75 5.2 90 245
0.10
0.25 6.4
0.120
3.0 9-8210
116
60
250
6.35 0.25 6.4 75 5.2 90 245
0.10
0.25 6.4
0.188
3.4 9-8210
116
60
170
4.32 0.25 6.4 75 5.2 90 245
0.20
0.25 6.4
0.250
6.4 9-8210
132
60
85
2.16 0.25 6.4 75 5.2 90 245
0.30
0.25 6.4
0.375
9.5 9-8210
140
60
45
1.14 0.25 6.4 75 5.2 90 245
0.50
0.25 6.4
0.500
12.7 9-8210
143
60
30
0.76 0.25 6.4 75 5.2 90 245
0.80
0.25 6.4
0.625
15.9 9-8210
145
60
20
0.51 0.25 6.4 75 5.2 90 245
NR NR NR
0.750
19.1 9-8210
145
60
18
0.46 0.25 6.4 75 5.2 90 245
NR NR NR
NOTE!
* Gas pressure shown is for torches with leads up to 25’ / 7.6 m long. For 50’ / 15.2 m leads, the gas pressure shall be
set at 4.8 bar.
** Total ow rate includes plasma and secondary gas ow.