Etatron eOne MF 0110 User Manual

Part B: Attaching suction & foot lter tubing
Cut clear tubing
in two pieces that
are the correct
size for your
application.
Attach one of the
two clear PVC
tubes to the
suction valve
following steps
2 - 5 in part A.
Attach the foot
filter (using
same process as
above), to other
end of clear PVC
tubing. Place into
the stock tank.
Slide the second
clear PVC tube
onto the priming
barb, and place
into the
stock tank.
eOne MF 0110 Quick Start Guide
• eOne MF pump
• Bracket Mounting Kit
• Operating instructions
and maintenance manual
• Allen Wrench (to remove solenoid
head when needed)
• Hose Packet
- Opaque, Rigid PE Tubing for
the Discharge
- Clear, Flexible, PVC Suction Tube
- Injection Valve
- Foot Filter
NOTE: Remove safety labels before installing
and remember pumps may hold water inside.
Part A: Attaching the opaque tubing to
the injection valves
Remove the
top discharge
valve nut.
Remove the
protective cap
from the nut and
discard.
Insert the opaque
tubing through
the nut. Slide the
locking collar
and insert the
hose nozzle
over the tube
creating a
compression
fitting.
Screw the nut
back onto the
discharge valve.
Hand tighten.
Attach other end
of tubing to the
injection stem,
follow steps 3 and
4. Install injection
stem into the
water line.
Flow Rate 0.26 GPH, Max. Pressure 145 PSI
Part C: Connecting the Water Meter
Tools needed: punch, small and standard
size at head screwdriver
Remove bottom
front cover using a
standard flat head
screw driver.
Remove the
rubber cap on
the left.
Using a punch
tool, punch a small
hole through the
rubber cap.
Insert the Water
Meter wires
through the hole in
the cap.
Run the wires
back through the
hole in the front
cover. Reinsert
the rubber cap.
Insert wires on
3
rd
and 4
th
holes
from left. Push
button and insert
wires using small
screwdriver.
Make sure they
are connected
properly.
1
2
3
4
5
Included in the Box
Discharge
Valve
Priming
Barb
Suction
Valve
Air Bleed
Valve
1
2
3
4
1
2
3
4
5
6
Injection stem has
1/2”, 3/8” and M10
MPT thread options.
Cut to your
specifications.
Insert into water line
so that the end of
injection valve is
midway in the pipe.
(Continue to back)
DO NOT CUT
passed this point

Etatron eOne MF 0110 Specifications

General

Pressure	10 bar
Pump Head Material	PVDF
Diaphragm Material	PTFE
Control	Manual
Voltage	230 V
Frequency	50 Hz

Summary

eOne MF 0110 Quick Start Guide

Included in the Box

Lists all components included in the pump package for installation and operation.

Part A: Attaching the opaque tubing to the injection valves

Step 1-4: Attaching Opaque Tubing

Details the process of connecting the opaque discharge tubing to the pump's discharge valve.

Step 5: Install Injection Stem

Connects the tubing to the injection stem and installs it into the water line.

Part B: Attaching suction & foot filter tubing

Attaching Suction and Foot Filter Tubing

Guides on connecting the clear PVC suction tubing and foot filter to the pump and stock tank.

Part C: Connecting the Water Meter

Wiring the Water Meter

Instructions for connecting the Water Meter wires to the pump's internal terminals.

Priming Instructions

Part D: Priming the pump

Step-by-step guide to initiate the pump's priming sequence and enter setup mode.

Part E: Programming the pump 1xN(M) MODE

Configures the pump to stroke a specific number of times per water meter pulse.

eOne Installation Overview

Diagram and Safety Notes

Provides an overall installation diagram and important caution and note statements.