This document is a Use and Care Guide for the Everbilt Stainless Steel Waterfall Pump, Model # SSB300, SKU # 1000026647. It provides detailed information on the pump's application, technical specifications, installation, operation, maintenance, and troubleshooting.

Function Description

The Everbilt Stainless Steel Waterfall Pump is a submersible utility pump designed specifically for waterfall or fountain applications. Its primary function is to pump water, making it suitable for creating water features in gardens or other outdoor settings. The pump is not tested or approved for use in swimming pools or salt-water marine areas.

Important Technical Specifications

SKU: 1000026647
Model #: SSB300
HP: 1/2
Power Supply: 115V, 60 Hz, 15 Amp Circuit
Liquid Temperature Range: 32°F to 95°F (0°C - 35°C)
Discharge Size: 1-1/4 in. MNPT
GPH of Water @ Total Feet Of Lift:
- 0 ft: 3600 GPH
- 5 ft: 2880 GPH
- 10 ft: 2400 GPH
- 15 ft: 1950 GPH
- 20 ft: 1560 GPH
- 25 ft: 900 GPH
Max. Lift: 29 ft

Usage Features

Submersible Design: The pump is designed to be submerged in water for operation.
Application: Exclusively for waterfall and fountain applications.
Electrical Safety: Equipped with an approved 3-conductor cord and 3-prong grounded plug. It requires a properly installed and grounded 3-prong, grounding-type receptacle (GFCI outlet recommended). A 10 Amp fuse or circuit breaker is recommended for circuit protection.
Flow Control: A diverter valve can be installed between the discharge pipes to adjust the pump's flow rate. This is particularly useful when controlling the flow over a waterfall in a vault.
Installation:
- Should be installed on a solid base to maintain vertical orientation and maximum efficiency, preventing clogging.
- If the bottom surface of the pond or waterfall is dirty, the pump can be raised slightly to reduce debris intake.
- Connecting a PVC adapter to a foot valve is part of the installation process.
- It is not recommended to install a check valve, as it might cause airlock. If a check valve is installed, a 1/8 in. hole should be drilled between the check valve and pump discharge.
Operation Conditions:
- The pump can run when not completely covered by water, but the water level must cover at least half of the pump.
- Running the pump dry (water level less than 1.5 inches) will cause overheating, wear out the pump, and void the warranty.
Thermal Protection: The motor has a thermal protector that trips if the motor becomes too hot, resetting once the motor cools down. The pump may start unexpectedly if plugged in.
Safety Precautions:
- Always disconnect power before servicing.
- Do not handle the pump or motor with wet hands or when standing on a wet or damp surface.
- Do not touch the motor housing during operation as it operates at high temperatures.
- Do not pump flammable or explosive liquids.
- Wear safety goggles when working with pumps.
- Protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking or using damaged cords.
- Secure the discharge line before starting the pump to prevent whipping.
- Do not lift the pump by the power cord.
- Extension cords are not recommended as they may not deliver sufficient voltage and pose safety hazards if damaged or if connections fall into water.

Maintenance Features

Screen Cleaning: The inlet screen should be kept clean at all times. Periodically inspect and remove all debris from the pump suction screen.
Debris Removal (Clogged Pump):
1. Unplug the pump from electrical power.
2. Unscrew the stainless screws (6) and remove the screen (5).
3. Unscrew the stainless screws (4) and remove the suction plate (3).
4. Use a flathead screwdriver to hold the shaft (1) and turn the impeller counterclockwise to release it.
5. Remove debris from around the shaft (1) and on/under the impeller (2).
6. Reassemble the impeller (2), suction plate (3), and screen (5).
Winterization: The pump should be taken out of freezing water in the winter. Freezing water can damage the pump, leading to water leakage in the motor housing and potential electrical shorts.
Regular Inspection: Periodically inspect the pump and system components to ensure the suction screen is free of mud, sand, and debris. Check the hose for holes, wear, kinks, and sharp angles, and ensure all hose connections are tight.
Motor Housing: Do not disassemble the motor housing, as it contains no repairable internal parts, and disassembly can cause leakage or electrical wiring issues.

Warranty

The manufacturer provides a two-year warranty from the date of purchase, covering defects in materials and workmanship under normal use and service. The warranty is valid for the original consumer purchaser and requires the original receipt of purchase. It does not cover damage from misuse, abuse, accident, modifications, alterations, neglect, mishandling, improper installation, or operational failures caused by corrosion, rust, or foreign materials. The purchaser is responsible for all labor and shipping charges for warranty replacements.

Everbilt SSB300 - Package Contents; Specifications

Table of Contents

Related product manuals