Chip Collection
This tool is provided with a chip collector compartment. When the chips
accumulate up to the see-through window, remove the cover, clean out
the cover, then replace it, and tighten the knobs. Notice: The metal chips
inside the cover may be very hot and sharp - do not touch with bare
hands.
Dust Extraction
To allow the tting of a dust extractor pipe, remove the small black cover
located at the top left of the chip collection cover. Replace the cover
when a dust extractor is not in use.
Maintenance And Troubleshooting
Keep tool, cord, and carry case clean and free from chips. Avoid using
cleaning products, which include benzene, trichloroethelene, chloride,
and ammonia as these can damage plastic parts. In case of electrical or
mechanical malfunction, immediately switch off the tool and disconnect
the plug. Excessive sparking may indicate the presence of dirt in the
motor or worn out carbon brushes. Check for wear and replace when
they reach 1/4” (6mm). For all other service please contact our Technical
Helpline.
Lubrication
Your machine is lubricated at the factory with sufcient lubricant to last for
approximately 72 hours of operation. To add lubricant, it is necessary to
dismantle the tool. Please contact our Technical Helpline for information
regarding this operation.
Accessories – Genuine Evolution Brand Blades
20T 7-1/4” (185mm) TCT Multi Blade
Notice: Normal wear and tear and damage caused by misuse
is NOT covered under the 12-Month guarantee.
ENVIRONMENTAL PROTECTION
Recycle unwanted materials instead of disposing of them
as waste. All tools, hoses and packaging should be sorted,
taken to the local recycling center and disposed of in an
environmentally safe way.
Recyclable Materials Analysis List
Material Weight(Kg) Percentage (%)
Aluminum
Cast Iron
Iron Plate
Plastics
Others
Total
1.1
0
3.3
0.7
0.1
5.20
21.10%
0.0%
63.40%
13.40%
1.90%
99.80%
Major Packaging Materials
Material Weight(Kg)
Carton
Polystyrene
Plastic
Polypropylene
Others
Total
1.16
0.00
3.43
0.001
0
4.59
UMWELTSCHUTZ
Recyceln Sie unbrauchbare Materialen nicht mit dem
normalen Restmüll. Alle Geräte, Kabel und Verpackungen
sollten sortiert und auf eine umweltfreundliche Art entsorgt
und recycelt werden.
Liste für recyclebare Materialien
Material Gewicht (Kg) Anteil in (%)
Aluminium
Gusseisen
Metallplatten
Plastik
Andere
Gesamt
1.1
0
3.3
0.7
0.1
5.20
21.10%
0.0%
63.40%
13.40%
1.90%
99.80%
Hauptmaterialien der Verpackung
Material Gewicht (Kg)
Karton
Styropor
Weiche Kunststoffe
Kunststoffe
Andere
Gesamt
1.16
0.00
3.43
0.001
0
4.59
PROTECTION DE L’ENVIRONNEMENT
Recyclez les matières usées ou indésirables au lieu de
les jeter. Tous les outillages, composants et emballages
doivent être collectés, et déposés au centre de recyclage
local pour préserver l’environnement.
Liste analytique des matières recyclables
Matière Poids (Kg) Pourcentage ( % )
Aluminium
Fonte
Fer
Plastiques
Autres
Total
1.1
0
3.3
0.7
0.1
5.20
21.10%
0.0%
63.40%
13.40%
1.90%
99.80%
Composants majoritaires des emballages
Matière Poids (Kg)
Carton
Polystyrène
Polyéthylene basse densité
Polypropylène
Autres
Total
1.16
0.00
3.43
0.001
0
4.59
PROTEZIONE DELL'AMBIENTE
Ricicli i materiali indesiderabili invece di averli come spreco.
Tutti gli attrezzi, tubi essibili ed imballaggio dovrebbero
essere classicati , presi al centro di riciclaggio locale
ed essere disfatti di in una forma sicura per il condizione
ambientale .
Lista di Analisi di Materiali Riciclabile
Materiale Peso (Kg) Percentage ( % )
Alluminio
Ferro di Getto
Placato di Ferro
Plastiche
Altri
Totale
1.1
0
3.3
0.7
0.1
5.20
21.10%
0.0%
63.40%
13.40%
1.90%
99.80%
Major Packaging Materials
Materiale Peso (Kg)
Cartone
Polistirolo
Polietilene di Densità Bassa
Polipropilene
Altri
Totale
1.16
0.00
3.43
0.001
0
4.59
MILJØVERN
Resirkuler uønskede materialer i stedet for å kvitte seg
med dem som avfall. Alle verktøy, slanger, emballasje bør
sorteres, tatt til det lokale resirkulerings senter og kvitte seg
med det på en miljømessig trygg måte.
3 4
To Next Page
Loading...
Need help?
General