Exmark Metro 4500-352

Questions and Answers

K
krileyAug 18, 2025
What to do if Exmark Lawn Mower engine loses power?
- T
  twoodardAug 18, 2025
  If your Exmark Lawn Mower engine loses power, it could be due to several reasons. First, the engine load might be excessive, so reduce the ground speed. Check if the air cleaner is dirty and clean or replace the air cleaner element. Also, verify the oil level in the crankcase and add oil if it's low. Make sure the cooling fins and air passages for the engine are not plugged; if they are, remove the obstructions. Check if the vent hole in the fuel cap is plugged; clean or replace the fuel cap if necessary. A dirty fuel filter can also cause power loss, so replace the fuel filter. If there's dirt, water, or stale fuel in the fuel system, contact an Authorized Service Dealer.
D
Daniel VelezAug 21, 2025
What to do if Exmark Lawn Mower has abnormal vibration?
- S
  sheltonearlAug 21, 2025
  If your Exmark Lawn Mower experiences abnormal vibration, several issues could be the cause. Start by checking if the cutting blades are bent or unbalanced and replace them if necessary. Ensure the blade mounting bolt is tightened securely. Inspect the engine mounting bolts and tighten them if they are loose. Also, check for loose engine pulleys, idler pulleys, or blade pulleys and tighten them as needed. If the engine pulley is damaged or the blade spindle is bent, contact an Authorized Service Dealer. Finally, examine the belt for damage and replace it if necessary.
J
Joseph LynchAug 25, 2025
Why Exmark Lawn Mower blades do not stop when disengaged?
- C
  Christina SpencerAug 25, 2025
  If the blades on your Exmark Lawn Mower do not stop when disengaged, it could be due to a few reasons. The blade brake might not be adjusted properly, so adjust the blade brake. Another possible cause is that the belt guide is not properly set, so adjust the belt guide to the proper position. Finally, the PTO engagement might not be properly set, so check the PTO engagement position.
Q
qdanielAug 28, 2025
How to fix Exmark Metro 4500-352 pulling left or right?
- I
  Ian WalkerAug 28, 2025
  If your Exmark Lawn Mower pulls to the left or right (with levers fully forward), several factors could be the cause. Start by checking the idler arm pulleys and drive sheaves for dirt and remove any mud or grass buildup. Ensure the wheel drive belt pulley scrapers are correctly adjusted. Lubricate the idler pivots if the idler pivot arms cannot pivot freely. Replace the drive belts as a set if they are worn, avoiding mixing new and worn belts. Correct the drive linkage adjustment if it is not correct. Finally, adjust the tire pressure in the drive tires to the correct level.
J
James HorneAug 31, 2025
Why Exmark Metro 4500-352 Lawn Mower has uneven cutting height?
- S
  Sara TownsendAug 31, 2025
  If your Exmark Lawn Mower has an uneven cutting height, there are several potential causes. The blades might not be sharp, so sharpen them. If the cutting blades are bent, install new ones. The mower deck might not be level, so level the mower deck from side-to-side and front-to-rear. The underside of the mower might be dirty, so clean it. Ensure the tire pressure in the drive tires is correct by adjusting it. If the blade spindle is bent, or the tips of adjacent blades are at an uneven cutting height, contact an Authorized Service Dealer. Lastly, check if the caster mounting brackets are loose and tighten the hardware if necessary.
M
Monique FrenchSep 4, 2025
What to do if Exmark Lawn Mower engine overheats?
- K
  Kristine CochranSep 4, 2025
  If your Exmark Lawn Mower engine overheats, it could be due to a couple of reasons. First, the engine load might be excessive, so reduce the ground speed. Additionally, check the oil level in the crankcase and add oil if it is low.
G
Gerald GarciaSep 6, 2025
Why Exmark Lawn Mower blades do not rotate?
- Y
  Yvette JacobsSep 6, 2025
  If the blades on your Exmark Lawn Mower do not rotate, the deck belt may be worn, loose, or broken, so install a new deck belt. Also, the deck belt might be off the pulley. In this case, install the deck pulley and check the idler pulley, idler arm, and spring for correct position and function.
A
apadillaSep 12, 2025
What to do if Exmark Metro 4500-352 Lawn Mower does not drive?
- M
  Mr. Kyle HillSep 12, 2025
  If your Exmark Lawn Mower does not drive, it could be because the transmission drive belt is worn, loose, or broken, so change the belt. Another possibility is that the transmission drive belt is off a pulley, so change the belt.
M
mariahjohnsonNov 13, 2025
Why Exmark Metro 4500-352 engine will not start?
- F
  fjenningsNov 13, 2025
  If your Exmark Lawn Mower engine won't start, starts hard, or fails to keep running, several factors could be the cause. First, check if the fuel tank is empty and fill it if needed. Ensure the fuel shutoff valve is open. For a cold engine, make sure the choke is in the 'ON' position, or 'OFF' for a warm engine, with the throttle control midway between 'SLOW' and 'FAST'. Other potential issues include a dirty fuel filter (replace it), dirt, water, or stale fuel in the fuel system (contact an Authorized Service Dealer), a dirty air cleaner (clean or replace it), corroded, loose, or faulty electrical connections (check and clean them), a defective relay or switch (contact an Authorized Service Dealer), a faulty spark plug (clean, adjust, or replace it), a disconnected spark plug wire (check ...