Exmark Lazer Z Series

Other manuals for Exmark Lazer Z Series

Setup Instructions6 pages

Questions and Answers

S
Stacy SmithAug 16, 2025
Why won't my Exmark Lazer Z Lawn Mower starter crank?
- M
  Maria ChoiAug 16, 2025
  If your Exmark Lawn Mower's starter isn't cranking, it could be due to several reasons: * The parking brake might not be engaged: set the parking brake. * The drive levers may not be in the neutral lock position: ensure they are properly positioned. * The battery might not have a full charge: charge the battery. * There may be corroded, loose, or faulty electrical connections: check and clean the connections, applying dielectric grease before reconnecting. * A fuse could be blown: replace the fuse. * In case of a defective relay or switch, it's best to contact an Authorized Service Dealer.
J
jennifer87Aug 22, 2025
Why is my Exmark Lazer Z Lawn Mower engine losing power?
- C
  christieanthonyAug 22, 2025
  If your Exmark Lawn Mower engine is losing power, consider the following: * The engine load may be excessive: reduce the ground speed. * The air cleaner might be dirty: clean or replace the air cleaner element. * The oil level in the crankcase could be low: add oil to the crankcase. * The fuel filter may be clogged with dirt: replace the fuel filter. * For issues related to dirt, water, or stale fuel in the fuel system, it's recommended to contact an Authorized Service Dealer.
D
Derek HarringtonAug 25, 2025
What to do if my Exmark Lawn Mower engine overheats?
- E
  Erik ChavezAug 26, 2025
  If your Exmark Lawn Mower engine is overheating, here are a few things to check: * The engine load may be too high: reduce the ground speed. * The oil level in the crankcase could be low: add oil. * The air filter might be dirty: clean or replace it. * The coolant level may be low: add coolant. * There might be debris on or around the radiator: remove any obstructions. * If the water pump or alternator belt is worn, loose, or broken, it's best to contact an Authorized Service Dealer.
T
Timothy WangAug 28, 2025
How to fix Exmark Lazer Z that pulls to one side?
- W
  Wanda GeorgeAug 28, 2025
  If your Exmark Lawn Mower pulls to the left or right even with the levers fully forward, here’s what you can check: * The tracking may need adjustment: adjust the tracking. * The tire pressure in the drive tires might not be correct: adjust the tire pressure. * The reverse indicator and motion control linkage could need adjustment: adjust them accordingly.
C
Christopher WigginsAug 31, 2025
Why are the blades not rotating on my Exmark Lawn Mower?
- J
  julie61Aug 31, 2025
  If your Exmark Lawn Mower blades do not rotate, consider the following: * The drive belt might be worn, loose, or broken: check the belt tension. * The drive belt could be off the pulley: inspect the belt for damage and replace if necessary; install the drive belt and ensure the belt guide is correctly positioned. * The deck belt may be worn, loose, or broken: install a new deck belt. * The deck belt could be off the pulley: install the deck pulley and check the idler pulley, idler arm, and spring for correct position and function. * A broken or missing idler spring: replace the spring. * The clutch has disengaged: the engine has overheated; determine cause of overheat (see Engine overheats). * The wings are not fully lowered: lower the wings.
Y
Yesenia MunozSep 3, 2025
Why is my Exmark Lazer Z Lawn Mower vibrating abnormally?
- D
  Desiree RodriguezSep 3, 2025
  If your Exmark Lawn Mower has an abnormal vibration, check these potential causes: * The cutting blade(s) may be bent or unbalanced: install new cutting blade(s). * The blade mounting bolt might be loose: tighten it. * The engine mounting bolts could be loose: tighten them. * A loose engine pulley, idler pulley, or blade pulley: tighten the appropriate pulley. * Install new belt if the belt is damaged. * For a damaged engine pulley or bent blade spindle, it's best to contact an Authorized Service Dealer.
J
John HayesSep 6, 2025
What to do if my Exmark Lazer Z does not drive?
- J
  johnfryeSep 6, 2025
  If your Exmark Lawn Mower isn't driving, it might be because: * The bypass valve is not closed tightly: tighten the bypass valve. * The hydraulic fluid level is low or too hot: add hydraulic fluid to the reservoir or allow it to cool down.
A
Alexandra JacksonSep 9, 2025
Why won't the clutch engage on my Exmark Lazer Z?
- L
  Linda HernandezSep 9, 2025
  If the clutch on your Exmark Lawn Mower won't engage, consider these possibilities: * A fuse is blown: replace the fuse and check coil resistance, battery charge, charging system, and wiring connections, replacing if necessary. * Low voltage supply at the clutch: check coil resistance, battery charge, charging system, and wiring connections, replacing if necessary. * Inadequate current supply: repair or replace the clutch lead wire or electrical system, and clean connector contacts. * The engine has overheated: determine the cause of the overheat (see Engine overheats). * The wings are not fully lowered: lower the wings.
A
Anthony HendersonSep 12, 2025
How to fix uneven cutting height on Exmark Lazer Z?
- L
  lisawilliamsSep 12, 2025
  If you're experiencing an uneven cutting height with your Exmark Lawn Mower, here are some things to check: * The blade(s) may not be sharp: sharpen the blade(s). * A cutting blade might be bent: install new cutting blade(s). * The mower deck may not be level: level the mower deck from side to side and front to rear. * The underside of the mower might be dirty: clean it. * The tire pressure in the drive tires may not be correct: adjust the tire pressure. * Replace blades, spindles and (or) check for damage to mower deck if tips of adjacent blades are at an uneven cutting height. * If the blade spindle is bent, it's best to contact an Authorized Service Dealer.
C
Crystal AlvarezNov 18, 2025
Why won't my Exmark Lazer Z Lawn Mower engine start?
- B
  Brandy RiceNov 18, 2025
  If your Exmark Lawn Mower engine won't start, starts with difficulty, or doesn't stay running, consider these potential causes: * The fuel tank might be empty: fill it up. * The oil level in the crankcase could be low: add oil. * The fuel filter may be clogged with dirt: replace it. * The air cleaner might be dirty: clean or replace the air cleaner element. * The seat switch may not be working correctly: check the seat switch indicator and replace the seat if necessary. * Check for corroded, loose, or faulty electrical connections: clean the connector terminals thoroughly with electrical contact cleaner, apply dielectric grease, and reconnect. * For dirt, water, or stale fuel in the fuel system, or a defective relay or switch, it is recommended to contact an Authorized Servi...

Summary

Introduction

Before Operating Your Mower

Instructs users to carefully read the entire manual before operating the mower.

Model and Serial Number Location

Identifies the location of the model and serial numbers on the product.

Warranty Information

Provides information on obtaining complete warranty details.

Safety

Safety Alert Symbol

Explains the meaning and use of the safety alert symbol in the manual and on the machine.

Safe Operating Practices

Guidelines for safe operation, including training and preparation requirements.

Operation

Instructions for safe machine operation, covering engine, lighting, and hazard avoidance.

Slopes Operation

Precautions and procedures for safe operation on slopes to prevent rollovers.

Using the Rollover Protection System (ROPS)

Proper use and importance of the ROPS for operator safety during potential rollovers.

Maintenance and Storage

Safety guidelines for performing maintenance and storing the machine properly.

Towing Safety

Safety precautions for towing the machine or towed equipment.

Safety and Instructional Decals

Importance of maintaining and understanding safety labels on the machine.

Specifications

Systems

Overview of the machine's key systems like engine and fuel.

Engine

Details on engine type, oil, and viscosity requirements.

Fuel System

Fuel capacity, recommendations, and important notes for diesel and biodiesel.

Electrical System

Information on charging system, battery, and fuses.

Operator Controls

Description of steering, motion control, PTO, and parking brake controls.

Hydrostatic Ground Drive System

Specifications for the hydrostatic transmission and wheel motors.

Tires & Wheels

Specifications for drive tires and front caster wheels.

Cutting Deck

Details on cutting widths, blade sizes, and deck design.

Dimensions

Physical measurements of the machine with different deck configurations.

Product Overview

Curb Weight

Weight specifications for different models and deck configurations.

Torque Requirements

Critical torque values for various fasteners and components.

Operation

Motion Control Levers

How to operate the levers for machine movement and steering.

RED Equipped Logic Display Unit (LDU)

Information on the LDU screen, buttons, and status lights.

Ignition Switch

How to start and stop the engine using the ignition switch.

PTO Engagement Switch

How to engage and disengage the PTO for blade operation.

Pre-Start

Essential pre-operation checks and fuel filling procedures.

Raise the Rollover Protection System (ROPS)

Steps to correctly raise and lock the ROPS for safe operation.

Starting the Engine

Step-by-step instructions for starting the engine safely.

Driving the Machine

General instructions and cautions for driving the machine.

Driving Forward

Steps and techniques for driving the machine forward.

Driving in Reverse

Steps and techniques for driving the machine in reverse.

Adjusting the Cutting Height-60 and 72 Inch Decks

How to adjust the cutting height for 60 and 72-inch decks.

Loading the Machine

Procedures and safety precautions for loading the machine onto a trailer.

Maintenance

Recommended Maintenance Schedule(s)

A schedule of required maintenance tasks based on operating hours.

Check Engine Oil Level

Procedure for checking engine oil level before each use.

Recommended Jump Starting Procedure

Step-by-step guide for safely jump starting the engine.

Check Mower Blades

How to inspect, sharpen, or replace mower blades.

Check Safety Interlock System

Verifying the proper function of safety interlock mechanisms.

Check Engine Starting Circuit Chart

Diagram showing conditions that prevent engine starting.

Check Shutdown Circuit Chart

Diagram showing conditions that initiate engine shutdown.

Check Hydraulic Fluid Level

Procedure for checking the hydraulic fluid level.

Change Engine Oil and Filter

Steps for changing the engine oil and filter.

Change Hydraulic System Filter and Fluid

Procedure for changing hydraulic filter and fluid.

Check Engine Coolant Level

How to check the engine coolant level.

Adjustments

General note about performing adjustments on the machine.

Parking Brake Adjustment

Procedure for adjusting the parking brake.

Motion Control Linkage Adjustment

How to adjust the motion control linkage for proper operation.

Cleaning

Clean Engine and Exhaust System Area

Procedure for cleaning debris from the engine and exhaust system.

Clean the Radiator

Steps for cleaning radiator fins to maintain cooling efficiency.

Clean Grass Build-Up Under Deck

How to remove grass buildup from the underside of the mower deck.

Waste Disposal

Guidelines for the proper disposal of used oil and batteries.

Troubleshooting

Starter does not crank

Common causes and corrective actions for starter issues.

Engine will not start, starts hard, or fails to keep running

Troubleshooting steps for engine starting and running problems.

Engine loses power

Diagnosis and solutions for engine power loss.

Engine overheats

Causes and remedies for engine overheating.

Uneven cutting height

Identifying and correcting uneven cutting height issues.

Blades do not rotate

Causes and solutions for blades not rotating.

Schematics

Electrical Schematic-Yanmar Engine 3 TNV80 FT

Wiring diagram for the Yanmar 3TNV80FT engine.

Electrical Schematic-Yanmar Engine 3 TNV88 C

Wiring diagram for the Yanmar 3TNV88C engine.

Electrical Schematic-Tractor (RED) 60 and 72 Inch Models

Electrical schematic for RED 60/72 inch models.

Hydraulic Diagram-60 and 72 Inch Models

Hydraulic system diagram for 60/72 inch models.

Exmark Lazer Z Series Specifications

General

Engine Brand	Kawasaki, Kohler
Engine Type	Air-cooled, 4-stroke, gasoline
Cutting Width	52 in, 60 in, 72 in
Deck Construction	Fabricated
Deck Material	Steel
Drive Type	Hydrostatic
Transmission	Hydrostatic
Forward Speed	Up to 12.5 mph
Reverse Speed	Up to 5 mph
Tires (Rear)	26 x 12-12 (depending on model)
Turning Radius	Zero-turn
Cutting Height	1.5-5 inches (adjustable)
Speed	Up to 12.5 mph
Warranty	5-year / 1, 500-hour (Engine warranty varies by manufacturer)