Exmark VIKING HYDRO User Manual (English)

Other manuals for Exmark VIKING HYDRO

Operator's Manual48 pages

Setup Instructions6 pages

Questions and Answers:

C
christopher61Aug 18, 2025
How to troubleshoot Exmark Lawn Mower engine that will not start?
- A
  Anthony HillAug 19, 2025
  If your Exmark Lawn Mower engine isn't starting, starts with difficulty, or won't stay running, consider these potential causes: * The fuel tank may be empty, in which case you should fill it. * The fuel shutoff valve could be closed; open it. * The throttle and choke might not be correctly positioned; adjust them accordingly. * A dirty fuel filter can cause this issue, so replace it. * Check the spark plug wire connection. * Ensure the shifter lever is in the neutral position. * Depress OPC levers. * Disengage the PTO.
E
Elizabeth GonzalezAug 21, 2025
What to do if my Exmark VIKING HYDRO Lawn Mower engine will not start?
- R
  Rodney StephensAug 21, 2025
  If your Exmark Lawn Mower engine won't start, first, ensure the key switch is in the “Run” position. Also, verify that the choke is in the “ON” position if the engine is cold.
L
Lisa ScottAug 23, 2025
Why does my Exmark VIKING HYDRO Lawn Mower engine lose power?
- C
  Crystal ReedAug 23, 2025
  If your Exmark Lawn Mower engine is losing power, there are several possible reasons: * The engine load might be excessive; try reducing the ground speed. * A dirty air cleaner can cause power loss; clean or replace the air cleaner element. * Low oil level in the crankcase can also lead to this issue; add oil to the crankcase. * Check for plugged cooling fins and air passages and remove any obstructions. * The vent hole in the fuel cap might be plugged; clean or replace the fuel cap. * A dirty fuel filter can restrict fuel flow, so replace it.
A
Andres GarciaAug 26, 2025
What to do if Exmark VIKING HYDRO Lawn Mower engine overheats?
- B
  Bonnie AdamsAug 26, 2025
  If your Exmark Lawn Mower engine is overheating, consider the following: * The engine load might be excessive, so reduce the ground speed. * Low oil level in the crankcase can cause overheating; add oil to the crankcase. * Check for plugged cooling fins and air passages; remove any obstructions to ensure proper airflow.
T
Thomas DavisAug 28, 2025
How to fix uneven cuts with my Exmark VIKING HYDRO Lawn Mower?
- J
  John ValenzuelaAug 28, 2025
  To fix uneven cuts with your Exmark Lawn Mower: - A more uniform cutting height may be achieved with higher tire pressure on rough terrain, while lower pressure provides more flotation. - Check blade spacers on each blade, the axle positions on each side, and the spacers on each front caster wheel, ensuring they are equal. - Confirm caster mounting brackets are secure by tightening all bolts. - Inspect blades tip to tip for straightness, ensuring they are within 3/16” (4.8 mm), or one blade width from being in line.
T
todd22Aug 30, 2025
What to do if my Exmark VIKING HYDRO Lawn Mower tracks to the left or right?
- S
  Shannon RomeroAug 30, 2025
  If your Exmark Lawn Mower tracks to the left or right, turn the knob on the right hydro control linkage in the direction the mower needs to be adjusted. Make adjustments in 1/4 turn increments until the mower tracks correctly.
J
Joyce HarperSep 1, 2025
Why does my Exmark VIKING HYDRO Lawn Mower vibrate abnormally?
- R
  Randy GillespieSep 1, 2025
  Abnormal vibration in your Exmark Lawn Mower can stem from several issues: * Bent or unbalanced cutting blades; install new cutting blades. * A loose blade mounting bolt; tighten the blade mounting bolt. * Loose engine mounting bolts; tighten the engine mounting bolts. * A loose engine pulley, idler pulley, or blade pulley; tighten the appropriate pulley. * A damaged belt; install new belt.
R
Robert YoungSep 4, 2025
What to do if Exmark Lawn Mower machine does not drive?
- P
  paulcontrerasSep 4, 2025
  If your Exmark Lawn Mower isn't driving, check these potential causes: * The bypass valve might not be closed tightly; tighten the bypass valve. * The drive or pump belt could be worn, loose, or broken; change the belt. * The drive or pump belt might be off a pulley; change the belt.
J
Justin YoungSep 6, 2025
How to fix uneven cutting height on Exmark VIKING HYDRO?
- D
  David YoungSep 6, 2025
  If your Exmark Lawn Mower is producing an uneven cut, consider these factors: * Dull blade(s); sharpen the blade(s). * Bent cutting blade(s); install new cutting blade(s). * The mower deck may not be level; level mower deck from side-to-side and front-to-rear. * A dirty mower underside; clean the underside of the mower. * Incorrect tire pressure in drive tires; adjust tire pressure in the drive tires.
S
Steve MolinaSep 8, 2025
Why does my Exmark VIKING HYDRO Lawn Mower pull to the left or right?
- M
  Mark HallSep 8, 2025
  If your Exmark Lawn Mower pulls to the left or right, it could be due to: * Tracking needing adjustment; adjust the tracking by turning knob on the right hydro control linkage in the direction that the mower needs to be adjusted to. Turn the knob in 1/4 turn increments until the mower tracks correctly. * Incorrect tire pressure in drive tires; adjust tire pressure in the drive tires.