F.W. Bell 5200 Series User Manual

List of Illustrations
Figure 1-1
Flux Lines of a Permanent Magnet........................
1-1
Figure 1-2
Hall Generator........................................................
1-2
Figure 1-3
Hall Probe Configurations......................................
1-3
Figure 2-1
Standard Transverse Probe...................................
2-4
Figure 2-2
Standard Axial Probe.............................................
2-5
Figure 2-3
Low Field Axial Probe.............................................
2-6
Figure 2-4
Zero Flux Chamber................................................
2-7
Figure 3-1
Probe Electrical Warning……………......................
3-1
Figure 3-2
Battery Location.....................................................
3-3
Figure 3-3
Connections...........................................................
3-3
Figure 3-4
Keypad...................................................................
3-4
Figure 3-5
Missing Probe Indication........................................
3-5
Figure 3-6
Power-Up Display...................................................
3-5
Figure 3-7
5280 Home Screen...............................................
3-7
Figure 3-8
5270 Home Screen.................................................
3-7
Figure 3-9
5200 Settings 1......................................................
3-8
Figure 3-10
5200 Settings 2......................................................
3-8
Figure 3-11
5200 Settings 3......................................................
3-8
Figure 3-12
5200 Settings 4......................................................
3-8
Figure 3-13
Time & Date Settings Page....................................
3-10
Figure 3-14
Example About Page..............................................
3-12
Figure 3-15
Home Screen Info Box – Not Zeroed.....................
3-18
Figure 3-16
Zero Auto Settings Page……................................
3-18
Figure 3-17
Zero Manual Settings Page....................................
3-20
Figure 3-18
Home Screen Info Box - Relative...........................
3-23
Figure 3-19
Measurement Log…..............................................
3-25
Figure 3-20
Adjusting the DC Offset of the Analog Output........
3-29
Figure 3-21
Probe Output versus Flux Angle............................
3-30
Figure 3-22
Probe Output versus Distance...............................
3-30
Figure 3-23
Figure 3-24
Figure 3-25
Figure 3-26
Flux Density Variations in a Magnet.......................
Battery Removal …………………………………..…
Battery Polarity………………...…….……………....
Battery Installation……………………………………
3-31
3-33
3-34
3-34
Figure 4-1
Condition, Event, and Enable Registers..................
4-5
Figure 4-2
Status Byte and Enable Registers...........................
4-5
Figure 4-3
Standard Event Registers……………………………
4-7
Figure 4-4
Measurement Event Registers………………………
4-8
Figure 4-5
Operation Event Registers…………………………..
4-8
Figure 4-6
Questionable Event Registers………………………
4-8
Figure 4-7
PC5200 Connection Issue Error Box.....................
4-23
Figure 4-8
PC5200 Logging.....................................................
4-23
Figure 4-9
PC5200 Logging Interface......................................
4-24
Table of Contents, Cont.
Section - 4 Remote Operation
USB INTERFACE CONNECTION …......................…………
4-1
REMOTE COMMAND STANDARDS …………....................…..
4-1
COMMAND FORMAT ……..............................……………...…..
4-1
ERROR BUFFER …………................................…………….…..
4-2
STATUS REGISTERS ……........................................…….....…
4-2
INFORMATION FOR REMOTE OPERATION ….......................
4-3
OTHER GENERAL 5280 FILE INFORMATION ….................…
4-4
STATUS BYTE AND REQUEST FOR SERVICE (RQS) …....…
4-5
STANDARD EVENT REGISTER ………................................…
4-7
MEASUREMENT EVENT REGISTER ……............................…
4-8
OPERATION EVENT REGISTER ……...................................…
4-8
QUESTIONABLE EVENT REGISTER …..........................……..
4-8
“COMMON” COMMAND SYNTAX ……..........................………
4-9
“COMMON” COMMANDS ……….......................................……
4-10
SCPI COMMAND SYNTAX ……......................................……..
4-12
SCPI COMMANDS …………...........................................………
4-13
ERROR MESSAGES AND COMMANDS …..................……….
4-14
STATUS COMMANDS ……....................………….……….……
4-15
MODE COMMANDS……….....................................…………….
4-17
RANGE COMMANDS …….......................................…...………
4-18
HOLD COMMANDS ………...........................................……..…
4-19
ZERO COMMAND …………...............................................……
4-20
RELATIVE COMMANDS ………..................................…………
4-20
MEASUREMENT COMMAND ….............................……………
4-20
ANALOG OUTPUT COMMAND …....................................…….
4-21
OPERATION COMPLETE STATUS ..........................................
4-22
PC5200.EXE – REMOTE PC CONTROL…..……………………
4-23
MODEL 5200 ERROR CODES ….........................................….
4-25
WARRANTY

F.W. Bell 5200 Series Specifications

General

Brand	F.W. Bell
Model	5200 Series
Category	Measuring Instruments
Language	English