Felder CF 741 - Page 112

A
Adjusting
Cross-cutting stop scale..............S01-13
planing height ............................A01-9
Digital readout............................V01-4
Joint ..........................................A01-7
Shaper height............................F01-14
Shaper angle ............................F01-14
Circular saw blade......................K01-7
Cutting height ............................K01-7
Cutting angle ..............................K01-7
Splitter ......................................K01-5
Chip thickness ............................A01-6
Slitting unit “Standard”................K01-8
Slitting unit “Industrial” ................K01-9
C
Changing shapers ..........................F01-9
Cleaning ........................see maintenance
Combination fence ........................C02-2
Commissioning ............................B05-12
Cross-cutting stop
installation ..................................S01-8
setting the scale ........................S01-13
Cutting
splinter-free ............................K01-8,9
with cross-cutting stop................K01-11
with bracket arm ......................K01-12
with power feed ........................K01-12
Cutting lengths ..............................S01-3
D
Declaration of Conformity (EC) ........B05-2
Degree indexing ..........................S01-15
Drilling
with / without depth stop ..........A01-16
a slot ......................................A01-16
Drills
suitable ......................................A01-2
clamping..................................A01-11
Dust collecting
The correct dust collector ............V01-6
Dust levels......................................B05-9
E
Electrical system ......................................
connection..................................V01-7
Operation ................................B05-13
I
Installation and removal
of shaper spindle ......................F01-10
Installation conditions ....................V01-5
Installing the bracket arm table ........S01-9
Intended use ............A01-2, K01-2, F01-2
J
Joiner bridge guard ......................A01-5
Jointing ......................................A01-12
L
Lateral stop ..................................S01-13
Longitudinal cuts ..........................K01-10
Lubrication......................see maintenance
M
Machine description........................B05-3
Maintenance
Joiner assembly ........................A01-17
Tablesaw unit............................K01-13
Shaper ....................................F01-21
Combination fence......................C02-3
Sliding table assembly ..............S01-15
N
Noise levels..................................B05-10
O
Operating information (general)......V01-5
Operation
Joiner assembly ..........................A01-5
Bracket arm table ......................S01-13
Drilling unit ..............................A01-11
Tablesaw unit..............................K01-4
Shaper........................................F01-5
Overhead saw guard......................K01-5
P
Planer arbor cover ........................A01-6
Planer blades
suitable ......................................A01-2
changing..................................A01-20
Push stick and push block..............K01-10
R
Remaining risks........A01-3, K01-3, F01-3
Retooling
Surfacing <-> thicknessing ..........A01-8
S
Safety instructions ....A01-3, K01-3, F01-3
general ......................................V01-6
Saw blades
changing....................................K01-6
suitable ......................................K01-2
Sawblade guard ............................K01-5
Service work ..................see maintenance
Shaper fence ..................................F01-5
Shaper speed
correct ......................................F01-12
changing ..................................F01-11
Shaping
edges ......................................F01-15
molding ....................................F01-26
with high-speed spindle ............F01-16
Insertion shaping ......................F01-17
Curve shaping ..........................F01-18
Mortise and tenon ....................F01-19
Sliding table
locking ....................................S01-10
assembly of Z, K, M, L, F, X..........S01-4
assembly of XL ............................S01-6
Use and working techniques ........S01-2
Slitter
"Industrie" ..................................K01-9
"Standard" ................................K01-8
Slitting belt ..................................K01-14
Slitting blades
changing....................................K01-6
suitable ......................................K01-7
Space requirements ..............B05-4,5,6,7
Storage ........................................V01-4
Surface planing ..........................A01-12
T
Tapering / edge beveling ............A01-13
Technical data................................B05-8
Thickness planing ........................A01-15
Transmission belt
Shaper ....................................F01-23
Planer arbor ............................A01-22
Feed ..................................A01-23,24
Tablesaw..................................K01-14
Transport ..........................V01-4,B05-12
U
Unloading....................................B05-13
W
Warranty ......................................V01-2
Working techniques
permitted ............A01-4, K01-4, F01-4
prohibited ............A01-4, K01-4, F01-4
Alphabetic index
Topic ............................Section-Page