Fender SPL-6000P User Manual

SPECIFICATIONS
DESIGNATION TYPE PR 200
OUTPUT POWER Stereo Continuous sine wave output power,
both channels driven +/- 1dB, 20 Hz to 20kHz, THD < 0.03%
150 W into 8 Ω, each channel
300 W into 4 Ω, each channel
MONO BRIDGE 300 W into 16 Ω
600 W into 8 Ω
SINGLE CHANNEL DRIVEN @ 1 kHz, 1% THD 8 Ω 179W
4 Ω 312W
POWER BANDWIDTH 10 Hz to 68 kHz
(3 dB down from rated power at less than 0.1% THD)
FREQUENCY RESPONSE +0 -3dB; 5 Hz to 68 kHz (at rated power, 8 Ω)
RISE TIME Less than 5.2 µSec
SLEW RATE Greater than 13.5 V/µSec
TOTAL HARMONIC
DISTORTION (THD) 20 to 20 kHz at rated power, 4 Ω. Less than 0.03%
HUM AND NOISE Below rated output, 4 Ω
20 Hz to 20 kHz broad band 95 dB
IEC A Weight 102 dB
DAMPING FACTOR Reference, 8 Ω
5 Hz to 20 kHz Greater than 30
1 kHz Greater than 175
INPUT IMPEDANCE Differential 33 kΩ
CHANNEL SEPARATION Below rated power, single channel operating
1 kHz, Greater than 65 dB
SENSITIVITY Referenced 1 kHz, +/- 0.25 dB
Stereo Mode +1.8 dBV (1.23V)
Bridged Mode +1.8 dBV
STATUS INDICATORS Each channel-Peak LED (red)
Power LED (green)
COOLING Two speed fan
GAIN CONTROLS Continuously variable attenuator, one per channel
MODE SWITCHING Stereo-Mono Bridge, Stereo-Dual Mono, two push button
switches
POWER REQUIREMENTS 1000W
DIMENSIONS
Weight 25 lbs. (11.3 kg)
Height 3.5 in. (8.9 cm)
Width 19 in. (48.3 cm)
Depth 15 in. (38 cm)
7
THIS EQUIPMENT CONFORMS TO
THE FOLLOWING DIRECTIVES :
EMC 89/336/EEC AND LV 73/23/EEC
A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORP.
CORONA, CA 91720 USA

Fender SPL-6000P Specifications

Power Output

stereo continuous sine wave output power into 8 Ω	150 W each channel
stereo continuous sine wave output power into 4 Ω	300 W each channel
mono bridge output power into 16 Ω	300 W
mono bridge output power into 8 Ω	600 W
single channel driven output power into 8 Ω	179 W
single channel driven output power into 4 Ω	312 W

Frequency and Sound

power bandwidth	10 Hz to 68 kHz
frequency response	+0 -3dB; 5 Hz to 68 kHz
rise time	Less than 5.2 µSec
slew rate	Greater than 13.5 V/µSec
total harmonic distortion	Less than 0.03%

Noise and Impedance

hum and noise broad band	95 dB
hum and noise IEC A Weight	102 dB
damping factor 5 Hz to 20 kHz	Greater than 30
damping factor 1 kHz	Greater than 175
input impedance	33 kΩ

Sensitivity and Separation

channel separation	Greater than 65 dB
sensitivity stereo mode	+1.8 dBV (1.23V)
sensitivity bridged mode	+1.8 dBV

Operating Conditions

cooling	Two speed fan
power requirements	1000W
status indicators	Peak LED (red), Power LED (green)
gain controls	Continuously variable attenuator, one per channel
mode switching	Stereo-Mono Bridge, Stereo-Dual Mono, two push button switches

Weight and Dimensions

weight	11.3 kg
height	8.9 cm
width	48.3 cm
depth	38 cm