To Next PageTo Next PageWhat to do if the water pressure is too high in my Ferroli ATLAS D 30 Ki 100 UNIT Boiler?
If the system water pressure is too high in your Ferroli Boiler, you should check the system. Also check the safety valve and the expansion tank.
What to do if the overtemperature protection is activated on my Ferroli ATLAS D 30 Ki 100 UNIT?
If the overtemperature protection is activated in your Ferroli Boiler, this could be due to several reasons. It might be caused by a damaged heating sensor, in which case you should check its positioning and operation. Alternatively, there might be no water circulation in the system, so verify the circulating pump. Another possible cause is air in the system; if so, vent the system to resolve the issue.
What causes a DHW sensor fault in a Ferroli ATLAS D 30 Ki 100 UNIT?
If there is a DHW sensor fault in your Ferroli Boiler, it is likely due to a damaged sensor. You should check the wiring or replace the sensor to resolve this issue.
What does delivery sensor 1 fault mean on a Ferroli Boiler?
A delivery sensor 1 fault in your Ferroli Boiler typically indicates a damaged sensor. To fix this, check the wiring or replace the sensor.
What should I do if my Ferroli Boiler shows a delivery sensor 2 fault?
If your Ferroli Boiler shows a delivery sensor 2 fault, the sensor is probably damaged. You should check the wiring or replace the sensor.
How to fix an external probe fault on a Ferroli Boiler?
An external probe fault in your Ferroli Boiler could be due to a damaged probe or shorted wiring, in which case you should check the wiring or replace the sensor. Alternatively, the probe might be disconnected after activating the sliding temperature; if so, reconnect the external probe or disable the sliding temperature.
How do I resolve a heating sensor fault in my Ferroli ATLAS D 30 Ki 100 UNIT?
If there is a heating sensor fault in your Ferroli Boiler, the sensor is likely damaged and needs to be replaced.
Why is my Ferroli ATLAS D 30 Ki 100 UNIT Boiler showing a supply voltage under 170V?
If the supply voltage is under 170V for your Ferroli Boiler, it indicates an issue with the electrical mains. Check the electrical system to resolve this problem.
What does a mains frequency fault mean on my Ferroli ATLAS D 30 Ki 100 UNIT?
A mains frequency fault in your Ferroli Boiler indicates a problem with the electrical mains. You should check the electrical system.
What causes a system water pressure sensor fault in a Ferroli ATLAS D 30 Ki 100 UNIT Boiler?
If your Ferroli Boiler shows a system water pressure sensor fault, it could be due to disconnected wiring. Check the wiring to resolve this issue.
Welcome message and overview of the boiler's advanced design, technology, reliability, and construction.
Details the layout of the control panel, including buttons, display indicators, and their functions.
Explains the step-by-step procedure for safely powering the boiler on and turning it off.
Covers adjustments for Summer/Winter mode, heating temperature, and hot water temperature settings.
Emphasizes that installation must be performed by qualified personnel adhering to current regulations.
Specifies requirements for the installation room, including ventilation, material clearance, and environmental conditions.
Details system requirements, safety valve connection, water quality, and antifreeze system considerations.
Explains connecting the burner to the diesel supply line, including filter installation and pipe length limits.
Outlines electrical grid connection, earthing, power supply adequacy, and room thermostat wiring precautions.
Describes the requirements for connecting the unit to a suitable flue system for safe and efficient operation.
Covers TEST mode, burner adjustments (pump pressure, nozzle, air), and combustion analysis.
Lists essential checks before first lighting, including fuel, water, electrical systems, and initial start-up steps.
Details periodic checks, boiler casing cleaning, and instructions for burner removal for maintenance.
Provides a comprehensive fault list with codes, possible causes, and recommended cures for boiler anomalies.
Illustrates the boiler's main components and connection points with detailed dimensions and labels.
Presents a graph showing circulator head losses versus flow rate for performance analysis.
Lists key technical specifications, capacities, ratings, and electrical data for the boiler models.
Shows the complete electrical wiring connections for the boiler unit, including component references.
General