What to do if my Ferroli Boiler shows incorrect system water pressure is too high?
If your Ferroli Boiler indicates incorrect system water pressure is too high, check the system. Also check the safety valve and the expansion tank.
What to do if my Ferroli Boiler activates overtemperature protection?
If the overtemperature protection activates in your Ferroli Boiler, it could be due to a damaged heating sensor, no water circulation, or air in the system. Check the heating sensor's positioning and operation, inspect the circulating pump, and vent the system to resolve these issues.
Why is my Ferroli Boiler showing a flame present signal when the burner is off?
If your Ferroli Boiler shows a flame present signal when the burner is off, it could be due to a photoresistance short circuit or extraneous light striking the photoresistance. Replace the photoresistance or eliminate the extraneous light source to fix this.
What does it mean if my Ferroli Boiler displays 'Delivery sensor 1 fault'?
If your Ferroli Boiler displays a 'Delivery sensor 1 fault', it could indicate a damaged sensor or wiring issues. Check the wiring or replace the sensor.
What does it mean if my Ferroli ATLAS D 30 SI UNIT displays 'Delivery sensor 2 fault'?
If your Ferroli Boiler displays a 'Delivery sensor 2 fault', it could indicate a damaged sensor or wiring issues. Check the wiring or replace the sensor.
What should I do if my Ferroli Boiler displays 'External probe fault'?
If your Ferroli Boiler displays an 'External probe fault', the probe might be damaged, the wiring could be shorted, or the probe might be disconnected after activating the sliding temperature. Check the wiring, replace the sensor if necessary, reconnect the external probe, or disable the sliding temperature.
What to do if my Ferroli ATLAS D 30 SI UNIT shows 'Heating sensor fault'?
If your Ferroli Boiler displays a 'Heating sensor fault', the sensor is likely damaged and needs to be replaced.
What does it mean if my Ferroli ATLAS D 30 SI UNIT Boiler displays 'Card parameter fault'?
If your Ferroli Boiler displays a 'Card parameter fault', it indicates a wrong card parameter setting. Check the card parameter and modify it if necessary.
What should I do if my Ferroli ATLAS D 30 SI UNIT displays 'System water pressure sensor fault'?
If your Ferroli Boiler displays a 'System water pressure sensor fault', it is likely due to disconnected wiring. Check the wiring.
What to do if my Ferroli Boiler shows 'Supply voltage under 170V'?
If your Ferroli Boiler indicates a 'Supply voltage under 170V', it suggests there is an electric mains trouble. Check the electrical system.
Provides critical safety instructions for installation, maintenance, and operation.
Introduction, control panel layout, and operational indicators.
Instructions on how to start up and shut down the boiler.
Overview of boiler adjustments including temperature, modes, and curves.
How to switch between summer and winter operating modes.
Instructions for adjusting the system water temperature.
Explanation of compensation curve settings for weather-dependent control.
General guidelines and requirements for boiler installation.
Specifies the required location and ventilation for boiler installation.
Details on connecting the boiler to the heating and hot water systems.
Instructions for connecting the burner, including flexible pipes and filter.
Guidance on connecting the boiler using coaxial flue pipes.
Guidance on connecting the boiler using separate flue pipes.
Procedures for activating TEST mode and adjusting burner settings.
Instructions for adjusting the pump pressure for optimal operation.
How to adjust the burner head and air shutter for optimal performance.
Checking electrode and baffle positioning after nozzle replacement.
Checks to be performed before first lighting and after maintenance.
Ensuring proper operation and efficiency of the boiler during use.
Periodic checks required for long-term correct operation of the unit.
Diagnostics system and troubleshooting guide for boiler faults.
Diagrams and list of main components and connections of the boiler.
Graph showing circulating pump head/pressure loss characteristics.
Table detailing technical specifications and performance data of the boiler.
General| Type | Condensing |
|---|---|
| Fuel Type | Natural Gas / LPG |
| Thermal power | 30 kW |
| Nominal heat output | 30 kW |
| Maximum working pressure | 3 bar |
| Weight | 34 kg |
| Electrical connection | 230V / 50Hz |
| Ignition | Electronic |
| Fuel | Natural Gas, LPG |
| Water content | 4.5 liters |
| Mounting | Wall-mounted |
To Next Page