Ferroli DIVACONDENS F D User Manual (English)

Questions and Answers:

T
Tasha LeeAug 21, 2025
Why Ferroli DIVACONDENS F D has no burner ignition?
- L
  Lucas CraigAug 21, 2025
  If the Ferroli Boiler's burner fails to ignite, there might be several reasons. First, ensure there is a regular gas flow to the boiler and that any air has been purged from the pipes. Then, inspect the wiring of the ignition/detection electrode, ensuring it's correctly positioned and free of deposits. Also, check the gas valve, replacing it if necessary, and verify that the gas valve wiring is properly connected. Finally, the ignition power might be too low, so adjust it accordingly.
J
Janice RodriguezAug 22, 2025
What to do if overtemperature protection activation in Ferroli Boiler?
- M
  Matthew YangAug 22, 2025
  If the Ferroli Boiler activates overtemperature protection, it could be due to several reasons. First, check the positioning and operation of the heating sensor. Also, check the circulating pump or vent the system to ensure proper water circulation and eliminate any air.
D
Derek BrownAug 25, 2025
What to do if Ferroli Boiler indicates a gas valve fault?
- J
  Jay MosleyAug 25, 2025
  If the Ferroli Boiler is showing a gas valve fault, check the wiring to ensure it is properly connected. If the wiring is intact, the gas valve itself may be faulty and require replacement.
I
isaachollowayAug 27, 2025
How to fix poor combustion fault in Ferroli Boiler?
- M
  Monica JenkinsAug 27, 2025
  If your Ferroli Boiler is experiencing poor combustion, the inlet/exhaust flue may be obstructed. Check the flue to ensure it is clear.
D
dgutierrezAug 27, 2025
Why does the exchanger protection trip in my Ferroli DIVACONDENS F D?
- T
  Troy BlanchardAug 28, 2025
  If the exchanger protection trips in your Ferroli Boiler, it could be due to a lack of HO system circulation. Check the circulating pump to ensure it is functioning correctly. Alternatively, there might be air in the system, in which case you should vent the system.
W
wmartinAug 29, 2025
What causes 'Flame present signal with burner off' in Ferroli DIVACONDENS F D?
- J
  Jaclyn Mendoza DVMAug 29, 2025
  If your Ferroli Boiler displays a 'Flame present signal with burner off' message, the electrode may be faulty. Check the ionisation electrode wiring. Alternatively, there may be a card fault; in this case, check the card.
A
Andrea FordAug 31, 2025
How to troubleshoot external probe fault in Ferroli Boiler?
- J
  Jose MillerAug 31, 2025
  If your Ferroli Boiler is showing an external probe fault, it could be due to a damaged probe or shorted wiring. Check the wiring or replace the sensor. It could also be due to the probe being disconnected after activating the sliding temperature. Reconnect the external sensor or disable the sliding temperature.
A
Amy KirbySep 2, 2025
What causes combustion control fault in Ferroli Boiler?
- B
  Benjamin ElliottSep 2, 2025
  If your Ferroli Boiler is showing a combustion control fault, the fan or fan wiring may be faulty, so check them. Alternatively, the baffle may be faulty and require replacement. Finally, the flue may not be correctly sized or is obstructed, so check the flue.
R
Ryan HallSep 4, 2025
What to do if Ferroli DIVACONDENS F D displays incorrect system water pressure?
- M
  Madison BondSep 4, 2025
  If the Ferroli Boiler is showing an incorrect system water pressure, it might be too low; in that case, fill the system. Alternatively, the water pressure switch might be damaged or not connected, so check the sensor.
J
jennifer51Sep 5, 2025
Why Ferroli DIVACONDENS F D has no flame after the ignition phase?
- R
  Regina RobertsSep 5, 2025
  If your Ferroli Boiler is not igniting after the ignition phase, the gas pressure may be low. Check the gas pressure. It's also possible that the burner minimum pressure setting is incorrect, so check the pressures.